Search found 10 matches
- Thu Mar 04, 2021 3:40 am
- Forum: YSF Specific Support
- Topic: Random receive termination
- Replies: 5
- Views: 3338
Re: Random receive termination
Thanks for the information. I will continue on my quest to get it understood if not working...
- Wed Mar 03, 2021 10:43 pm
- Forum: YSF Specific Support
- Topic: YSF to P25 via Pi-Zero?
- Replies: 3
- Views: 2297
Re: YSF to P25 via Pi-Zero?
I also have an FT3D and use the YSF2P25 mode. Here is what I do. I have the YSF startup host set to Parrot...just my preference. Enter WiresX mode on the FT3D To get to YSF2P25 first unlink anything you might have linked. Then connect to YSF2P25 with the radio or you could use the link manager on th...
- Wed Mar 03, 2021 10:28 pm
- Forum: YSF Specific Support
- Topic: Random receive termination
- Replies: 5
- Views: 3338
Re: Random receive termination
Thanks for the information on the Kernels. Are there known issues with some of the MMDVM_HS hats? The two I have are from different manufacturers but are of similar design. The first one had a bead that was supposed to be loaded in a 3.3V supply filter but which was actually loaded in the spot for t...
- Wed Mar 03, 2021 8:07 pm
- Forum: YSF Specific Support
- Topic: RX Via Hotspot ok, byt cannot TX
- Replies: 5
- Views: 2679
Re: RX Via Hotspot ok, byt cannot TX
This may be a dumb question, but is the MMDVMHost service running? I have seen it not start occasionally.
Jim
Jim
- Wed Mar 03, 2021 7:55 pm
- Forum: YSF Specific Support
- Topic: Random receive termination
- Replies: 5
- Views: 3338
Re: Random receive termination - New information
I have been continuing to try to figure out what is going on with the hotspot dropping my receive signal. Since I have two hotspots now I decided to set both up into the YSF parrot and see if both would experience the drops at the same time. That might implicate my FT3D radio as a potential cause. W...
- Wed Feb 24, 2021 6:19 pm
- Forum: YSF Specific Support
- Topic: YSFGateway Not Starting
- Replies: 15
- Views: 7613
Re: YSFGateway Not Starting
I went back and re-imaged my uSD card with the 4.1.4 pi-star image and after configuration on a Pi 3B+ I saw the problem where the YSFGateway service would not start. As others have mentioned, imaging with 4.1.2 and then upgrading to 4.1.3 and 4.1.4 "solves" this problem and it worked for ...
- Wed Feb 24, 2021 6:02 pm
- Forum: YSF Specific Support
- Topic: Random receive termination
- Replies: 5
- Views: 3338
Re: Random receive termination
I received the second MMDVM_HS hat and it has the same behavior as the first, randomly dropping receive. I re-imaged the uSD card on the Pi3B+ with the 4.1.4 Pi-Star version and when properly configured, the YSFGateway service would never start. I followed what I read others have done: Start with th...
- Thu Feb 18, 2021 6:49 pm
- Forum: YSF Specific Support
- Topic: Random receive termination
- Replies: 5
- Views: 3338
Random receive termination
I have been using YSF2P25 quite a bit and I have noticed that occasionally while I am transmitting the hotspot will act like I unkeyed when I hadn't. The stations I was talking with say my transmission just stops. I now keep an eye on the dashboard and when I see the drop I immediately unkey and key...
- Thu Feb 18, 2021 5:41 pm
- Forum: YSF Specific Support
- Topic: YSFGateway Not Starting
- Replies: 15
- Views: 7613
Re: YSFGateway Not Starting
Are you referring to settings on the Expert YSF GW page? I just checked and in both the General and APRS blocks my call is there since I set it on the Configuration page. Had you done that? Just to add confusion...When I turned on the hotspot this morning I expected I would have to go and start the ...
- Thu Feb 18, 2021 6:28 am
- Forum: YSF Specific Support
- Topic: YSFGateway Not Starting
- Replies: 15
- Views: 7613
Re: YSFGateway Not Starting
I am also fairly new. I am running an MMDVM_HS hat on a Pi 3B+ with the latest Pi Star version (4.1.4) updated today (Dashboard date is 20210212). The hat firmware is 1.5.2. I have the configuration settings set for YSF and YSF2P25 and all seems to work...except when I power up or reboot the YSFGate...