Search found 928 matches

by KE7FNS
Sun Sep 27, 2020 8:16 am
Forum: Nextion Screens
Topic: Nextion Driver 1.18 released
Replies: 2
Views: 242

Re: Nextion Driver 1.18 released

Hallo, when i type in SSH acces : sudo NextionDriverInstaller/install.sh i get that comand is not found. I run od the 4.1.2 pistar software, 1.4.17 dual hat modem en RPI 3b+ Any Ideas? Yeah, you are not in the correct directory when you are trying to run the install script. Most likely you followed...
by KE7FNS
Sun Sep 27, 2020 2:55 am
Forum: Pi-Star General Support
Topic: How to find ip for hotspot
Replies: 1
Views: 22

Re: How to find ip for hotspot

I've been able to log into pi-star and configure hotspot, just can't get up address so it will load under home wifi. Any suggestions? Your password probably has characters that the dashboard doesn't like, or you are typing it incorrectly. Use the wifi builder instead. https://www.pistar.uk/wifi_bui...
by KE7FNS
Sat Sep 26, 2020 6:06 am
Forum: Everything Else
Topic: LTE Hat
Replies: 3
Views: 62

Re: LTE Hat

What are your thoughts? I looked at it briefly and I couldn't find how exactly it communicates with the RPi over the GPIO, I suspect it uses the serial port, and if that is the case then it is going to conflict with the MMDVM hat. So in that case you are going to need a hat that connects over USB a...
by KE7FNS
Sat Sep 26, 2020 6:03 am
Forum: WiFi Setup
Topic: WI-FI CONFIG
Replies: 2
Views: 50

Re: WI-FI CONFIG

i have been trying to get my hot spot (pi-star) hotspot. toaccess my hughesnet internet... i select the hug 2 connection and enter the proper password and all that happens is it starts blinking and wont connect to the internet? what am i doing wrong? mike KL7XK Your password probably has characters...
by KE7FNS
Wed Sep 23, 2020 6:25 am
Forum: Feature Requests
Topic: Nmea rs232 output
Replies: 2
Views: 130

Re: Nmea rs232 output

Heres something I wrote that "might" work. It isn't as easy as what I thought, there is a checksum so if the checksum calculation is wrong the message is going to be invalid. I'd be surprised if it worked, but it might. Also, if your radio isn't keeping the time, change the CR2032 batteries (one is ...
by KE7FNS
Tue Sep 22, 2020 8:49 pm
Forum: WiFi Setup
Topic: Wifi Network change
Replies: 13
Views: 278

Re: Wifi Network change

How can I get back into the pi-star software so I can correct the WiFi info? Normally if pi-star can't find a wifi access point to connect to after 120 seconds it creates its own access point for you to connect to. You also didn't say which model RPi you have, if you have a RPi with a network port ...
by KE7FNS
Tue Sep 22, 2020 5:26 am
Forum: Other MMDVM Modem Boards
Topic: Analog FM mode working on MMDVM Repeater
Replies: 6
Views: 1046

Re: Analog FM mode working on MMDVM Repeater

Well I can say that it definately works! I didn't realize you were the same person from the other thread. Most people that are asking about FM have a board that doesn't support it which is why I said that. Again, you shouldn't be asking about which version of what firmware someone else used. You sh...
by KE7FNS
Tue Sep 22, 2020 5:21 am
Forum: Feature Requests
Topic: Nmea rs232 output
Replies: 2
Views: 130

Re: Nmea rs232 output

Hi, My pistar is connected 24/24h. It's possible to add an output serial port sending NMEA information ? My idea is to feed the IC-7100 and the ID-5100 with simulated GPS information ( fixed position, send the time and date correctly) since those equipment lose the clock information when they are d...
by KE7FNS
Sun Sep 20, 2020 7:52 pm
Forum: Other MMDVM Modem Boards
Topic: Analog FM mode working on MMDVM Repeater
Replies: 6
Views: 1046

Re: Analog FM mode working on MMDVM Repeater

G0FHM wrote:
Sun Sep 20, 2020 8:07 am
I have a BI7JTA board, and the current firmware doesn't like FM
Only processors running 180Mhz or higher are capable of running FM.

Also I think you might have a board based on MMDVM_HS and not MMDVM and in that case MMDVM_HS doesn't work with FM at all.
by KE7FNS
Sun Sep 20, 2020 7:48 pm
Forum: Software Support
Topic: FM
Replies: 11
Views: 347

Re: FM

Now I just need to find the code! The only code that is on BI7JTA's site is the current code, which appears to have been stopped at that version. I've tried others, but the modem hasn't liked it, and i've had to revert to the current code. Will have to keep digging! Github tells you where the code ...