Search found 41 matches

by WB4SJN
Mon Dec 26, 2022 1:27 am
Forum: YSF Specific Support
Topic: Problem with YSF.
Replies: 1
Views: 3949

Problem with YSF.

I am using my new FT70 DR to connect to ysf through pi-star. It connects but only for a second or two then it drops. Sometime the BER is fine and sometimes the BER is as high as 15. Any help would be appreciated. Merry Christmas. 73.
by WB4SJN
Tue Jun 21, 2022 2:19 am
Forum: Pi-Star General Support
Topic: pi-star and WPA
Replies: 1
Views: 370

pi-star and WPA

I have an sd card with the boot section and I added wpa suplicant to it. Now how do I get it to work with my hotspot? Any help greatly accepted.
by WB4SJN
Sat Nov 20, 2021 1:49 am
Forum: Pi-Star General Support
Topic: New Internet
Replies: 0
Views: 683

New Internet

I lost my internet unexpecedly but I now have a new internet. I know there is a way to get back in to reset the internet, at least I think there is a way to do it. I just don't know how to do it. I am using a pi 3B with a nextion screen. Any help will be appreciated.
by WB4SJN
Sat May 08, 2021 12:03 am
Forum: Nextion Screens
Topic: Radio will not transmit with Nextion screen.
Replies: 2
Views: 6203

Re: Radio will not transmit with Nextion screen.

Thank you for your concern. I found the problem. We had set the TX/RX offsets at -500. I checked a file from a long time ago and found that the offsets were 500 not -500. When I reset the offsets back to 500 the radio responded but with a BER over 5. I dropped the offset to 400 and the BER is now le...
by WB4SJN
Fri May 07, 2021 4:13 am
Forum: Nextion Screens
Topic: Radio will not transmit with Nextion screen.
Replies: 2
Views: 6203

Re: Radio will not transmit with Nextion screen.

The TX/RX frequencies are 438.800. The screen is plugged into the pi3B+ USB port.
by WB4SJN
Fri May 07, 2021 1:22 am
Forum: Nextion Screens
Topic: Radio will not transmit with Nextion screen.
Replies: 2
Views: 6203

Radio will not transmit with Nextion screen.

I have a pi3B+ that has been working well. I added the nextion screen and it is operating as it should. It has all the information it is supposed to have. When I receive a signal it shows everything just as is supposed to.When I press the PTT on my radio nothing happens. A friend has 9 hotspots all ...
by WB4SJN
Mon Apr 19, 2021 7:29 pm
Forum: Pi-Star General Support
Topic: Up Dated to 4.1.4
Replies: 1
Views: 1313

Up Dated to 4.1.4

I recently updated to 4.1.4 and just noticed today that my DMR Configuration has changed. I was able to get my hotspot ID replaced but there are other changes that I am not familiar with. Is there a place to find what the configuration section should look like?
by WB4SJN
Thu Oct 22, 2020 8:33 pm
Forum: Raspberry Pi Foundation Hardware
Topic: Understanding Duplex MMDVM hat
Replies: 4
Views: 3962

Understanding Duplex MMDVM hat

I have the pi3B+ board. I have an Icom ID31 D-star radio. We have a D-star repeater the is on 146 mHz. If I put a Duplex MMDVM Hat on my pi will pi-star allow me to access the above mentioned repeater. I am still quite green when it comes to pi-star.
by WB4SJN
Wed Oct 21, 2020 8:52 pm
Forum: WiFi Setup
Topic: Wifi will not show up when in set-up
Replies: 1
Views: 1578

Wifi will not show up when in set-up

I am configuring a new SD card and everything is going well until I try to connect to wifi. I am on 192.168.50.1 and I have entered all the other information in configuration. I, then go to "Wireless Configuration, click "Configure WiFi" and enter the ssid and password for my internet...
by WB4SJN
Fri Sep 18, 2020 8:14 pm
Forum: DMR Specific Support
Topic: Receiving SMS Messages
Replies: 3
Views: 2495

Receiving SMS Messages

I am using the Anytone 868, a home made hotspot. I can send messages just fine but I can't receive them. My pi-star version is 4.1.2. Suggestions? Thanks.73.