Search found 42 matches
- Wed Apr 10, 2024 1:36 pm
- Forum: Pi-Star General Support
- Topic: Pi-star will not load on my iMac computer
- Replies: 1
- Views: 118
Pi-star will not load on my iMac computer
I have used pi-star on my Mac for a long time. Now when I type in the 192.168.1.188 it will not give the configuration page. Thanks for any help in this matter.
- Mon Dec 26, 2022 1:27 am
- Forum: YSF Specific Support
- Topic: Problem with YSF.
- Replies: 1
- Views: 3978
Problem with YSF.
I am using my new FT70 DR to connect to ysf through pi-star. It connects but only for a second or two then it drops. Sometime the BER is fine and sometimes the BER is as high as 15. Any help would be appreciated. Merry Christmas. 73.
- Tue Jun 21, 2022 2:19 am
- Forum: Pi-Star General Support
- Topic: pi-star and WPA
- Replies: 1
- Views: 428
pi-star and WPA
I have an sd card with the boot section and I added wpa suplicant to it. Now how do I get it to work with my hotspot? Any help greatly accepted.
- Sat Nov 20, 2021 1:49 am
- Forum: Pi-Star General Support
- Topic: New Internet
- Replies: 0
- Views: 697
New Internet
I lost my internet unexpecedly but I now have a new internet. I know there is a way to get back in to reset the internet, at least I think there is a way to do it. I just don't know how to do it. I am using a pi 3B with a nextion screen. Any help will be appreciated.
- Sat May 08, 2021 12:03 am
- Forum: Nextion Screens
- Topic: Radio will not transmit with Nextion screen.
- Replies: 2
- Views: 6385
Re: Radio will not transmit with Nextion screen.
Thank you for your concern. I found the problem. We had set the TX/RX offsets at -500. I checked a file from a long time ago and found that the offsets were 500 not -500. When I reset the offsets back to 500 the radio responded but with a BER over 5. I dropped the offset to 400 and the BER is now le...
- Fri May 07, 2021 4:13 am
- Forum: Nextion Screens
- Topic: Radio will not transmit with Nextion screen.
- Replies: 2
- Views: 6385
Re: Radio will not transmit with Nextion screen.
The TX/RX frequencies are 438.800. The screen is plugged into the pi3B+ USB port.
- Fri May 07, 2021 1:22 am
- Forum: Nextion Screens
- Topic: Radio will not transmit with Nextion screen.
- Replies: 2
- Views: 6385
Radio will not transmit with Nextion screen.
I have a pi3B+ that has been working well. I added the nextion screen and it is operating as it should. It has all the information it is supposed to have. When I receive a signal it shows everything just as is supposed to.When I press the PTT on my radio nothing happens. A friend has 9 hotspots all ...
- Mon Apr 19, 2021 7:29 pm
- Forum: Pi-Star General Support
- Topic: Up Dated to 4.1.4
- Replies: 1
- Views: 1339
Up Dated to 4.1.4
I recently updated to 4.1.4 and just noticed today that my DMR Configuration has changed. I was able to get my hotspot ID replaced but there are other changes that I am not familiar with. Is there a place to find what the configuration section should look like?
- Thu Oct 22, 2020 8:33 pm
- Forum: Raspberry Pi Foundation Hardware
- Topic: Understanding Duplex MMDVM hat
- Replies: 4
- Views: 4089
Understanding Duplex MMDVM hat
I have the pi3B+ board. I have an Icom ID31 D-star radio. We have a D-star repeater the is on 146 mHz. If I put a Duplex MMDVM Hat on my pi will pi-star allow me to access the above mentioned repeater. I am still quite green when it comes to pi-star.
- Wed Oct 21, 2020 8:52 pm
- Forum: WiFi Setup
- Topic: Wifi will not show up when in set-up
- Replies: 1
- Views: 1602
Wifi will not show up when in set-up
I am configuring a new SD card and everything is going well until I try to connect to wifi. I am on 192.168.50.1 and I have entered all the other information in configuration. I, then go to "Wireless Configuration, click "Configure WiFi" and enter the ssid and password for my internet...