Search found 10 matches
- Wed Jan 19, 2022 6:02 pm
- Forum: Hardware Support
- Topic: What MMDVM Board do you use?
- Replies: 8
- Views: 11397
Re: What MMDVM Board do you use?
I have several DVRPTR v1 boards using v1.6 Firmware running as HPHS "Hi Power Hotspots). The radios used to tx/rx are the Yaesu FT-7800/FT-7900/FT-8800/FT-8900. Easies radios to interface with the DVRPTR. PS2 Male to Male interface cable. Some cables need to have small portion of plastic remove...
- Sun Sep 27, 2020 10:37 pm
- Forum: Pi-Star General Support
- Topic: ERROR - Running two instances of Pi-Star
- Replies: 9
- Views: 5712
Re: ERROR - Running two instances of Pi-Star
Pi-STAR #1 KC2YYF (C) is running a Zum Radio Board (High Power Hotspot Board) https://www.hamradio.com/detail.cfm?pid=H0-016486 Host Name "pistarhigh" 145.630 Node Callsign KC2YYF RPT1 KC2YYF-C RPT2 KC2YYF-G The pi-star config Radio/Modem Type for the Zum Radio Board is "ZUM Radio-MMD...
- Wed Aug 26, 2020 3:19 pm
- Forum: Pi-Star General Support
- Topic: Icom RP2C controller using Pi-Star as a gateway
- Replies: 6
- Views: 2679
Re: Icom RP2C controller using Pi-Star as a gateway
Is there a document or YouTube documenting switching an ICOM D-STAR repeater stack (1 70cm) module and controller to Pi-STAR?
Dave N2KTO [email protected]
Thanks in advance.
Dave
Dave N2KTO [email protected]
Thanks in advance.
Dave
- Tue Jun 02, 2020 2:51 am
- Forum: D-Star Specific Support
- Topic: Need Elmer on setting up Pi-Star and radio for ICOM Access Point Mode
- Replies: 0
- Views: 1326
Need Elmer on setting up Pi-Star and radio for ICOM Access Point Mode
Hello, I have both the ICOM 51+2 and the ID-4100 with Bluetooth. I have in the past run Access Point mode on my ID-51+2 but seem to have forgotten how I did it. I am registered with the USTrust and have registered n2kto D and E for access point with the Trust. I have a pi3b+ and the opc 2350 cable, ...
- Wed Mar 04, 2020 11:55 am
- Forum: D-Star Specific Support
- Topic: learning cron command
- Replies: 21
- Views: 11321
Re: learning cron command
The original IRCDDB would allow you to take a D-STAR recording of your voice and add it as a voice announcement. I will have to go to my 5100 and see if I can make a recording and export it. Can't remember what the file format was.
- Wed Feb 26, 2020 4:19 pm
- Forum: D-Star Specific Support
- Topic: learning cron command
- Replies: 21
- Views: 11321
Re: learning cron command
I belong to a Search and Rescue team and was hoping that I might add a voice message like "The K9RRD Search and Rescue net will begin in 10 minutes on XRF020H this high power hotspot will disconnect from REF020A and reconnect to XRF020H for 45 minutes. The net will be a directed net. Net contro...
- Tue Feb 18, 2020 5:10 pm
- Forum: D-Star Specific Support
- Topic: learning cron command
- Replies: 21
- Views: 11321
Re: learning cron command
Ed,
It works!!!!!!!!!!!!!!!!!!!!!!!!!!! It was the line at the very end that I did not add!!!!!!!!!!!
Thank you very much for helping me get this right. I am normally on REF069C or REF020A.
Now on to tackle how to make announcements.
Thanks again for the help.
Dave
It works!!!!!!!!!!!!!!!!!!!!!!!!!!! It was the line at the very end that I did not add!!!!!!!!!!!
Thank you very much for helping me get this right. I am normally on REF069C or REF020A.
Now on to tackle how to make announcements.
Thanks again for the help.
Dave
- Tue Feb 18, 2020 4:59 pm
- Forum: D-Star Specific Support
- Topic: learning cron command
- Replies: 21
- Views: 11321
Re: learning cron command
Could the word sudo lacking be my issue?
- Tue Feb 18, 2020 4:57 pm
- Forum: D-Star Specific Support
- Topic: learning cron command
- Replies: 21
- Views: 11321
Re: learning cron command
I think I have complied to the format now including the "root" in the sentence. I have spaces before and after the "root". I added a test line at the bottom to allow me to see if pi-star would change to the reflectors specified. I applied the lines to pi-star and there still seem...
- Sat Feb 15, 2020 1:20 am
- Forum: D-Star Specific Support
- Topic: learning cron command
- Replies: 21
- Views: 11321
Re: learning cron command
So I tried to follow what is required to create a cron script to my existing script in pi-star but after applying changes to the cron and then rebooting the PI it does not work. What am I missing. I went to Expert/System Cron and made some changes. This is what my PI's cron looks like now. # /etc/cr...