Search found 194 matches

by VK7HSE
Thu Jun 25, 2020 4:43 am
Forum: Pi-Star General Support
Topic: FM Mode Support
Replies: 6
Views: 356

Re: FM Mode Support

You will need to update the firmware of your controller to be at least 20200520 (think that's the format used) otherwise it will not work as intended.

Cheers

Sent from my Pixel 4 XL using Tapatalk

by VK7HSE
Sun Jun 07, 2020 7:35 am
Forum: YSF Specific Support
Topic: Noises with FT-70D
Replies: 3
Views: 243

Re: Noises with FT-70D

Make sure you have disabled AMS on the frequency, otherwise you will get some data received as FM instead of C4FM.

Cheers

Sent from my Pixel 4 XL using Tapatalk

by VK7HSE
Sun Jun 07, 2020 7:27 am
Forum: WiFi Setup
Topic: Static IP Address in Pi_Star
Replies: 7
Views: 450

Re: Static IP Address in Pi_Star

You need to edit the file dhcpcd.conf this is located in /etc The format is as follows... Interface eth0 static ip_address=192.168.0.2/24 static routers=192.168.0.1 static domain_name_servers=192.168.0.1 interface wlan0 static ip_address=192.168.0.12/24 static routers=192.168.0.1 static domain_name_...
by VK7HSE
Sun Jun 07, 2020 7:14 am
Forum: MMDVM_HS Hat(s)
Topic: Duplex MMDVM board not working correctly?
Replies: 55
Views: 1472

Re: Duplex MMDVM board not working correctly?

Wow. That is absolutely what the issue was. I hadn't even realized that through mode was set. Thank you everyone for your help! (now I have to figure out what to do with the second dual hat I just ordered. :D ) Set one for Brandmeister and the other for DMR+ and enjoy both networks! Sent from my Pi...
by VK7HSE
Fri May 22, 2020 6:47 am
Forum: YSF Specific Support
Topic: how to setup pi-star to automatically reconnect to the YSF Reflector if looses connection
Replies: 6
Views: 456

Re: how to setup pi-star to automatically reconnect to the YSF Reflector if looses connection

Scroll down towards the bottom of the ysfgw config and look for the network and change revert from 0 to 1 and ensure that you have the target in the start up (most likely already is) Sent from my Pixel 4 XL using Tapatalk https://uploads.tapatalk-cdn.com/20200522/7b0049dc10b2f539f586ab8e2c1fba41.jpg
by VK7HSE
Tue Apr 21, 2020 11:25 am
Forum: NXDN Specific Support
Topic: what do you use
Replies: 1
Views: 593

Re: what do you use

I have a pair of Icom IC-F3161DS (VHF) IC-F4161DS (UHF) nxdn radio's.

These fall into the first generation category of radio as they don't have any bells & whistles (no text message or gps)

So for use with mmdvm they get the job done!

Sent from my Pixel 4 XL using Tapatalk



by VK7HSE
Mon Apr 20, 2020 3:53 pm
Forum: P25 Specific Support
Topic: P25 Linked to will not change (cannot unlink/change TG)
Replies: 5
Views: 783

Re: P25 Linked to will not change (cannot unlink/change TG)

The log files for Pi-star are available in /var/log/pistar and that will be populated with whatever modes you have active. You may want to add tg9999 to your P25 list to disconnect from a given reflector, but it's not necessary to disconnect before keying up another... Also tg10 is the local echo te...
by VK7HSE
Tue Apr 14, 2020 12:31 am
Forum: P25 Specific Support
Topic: P25 Linked to will not change (cannot unlink/change TG)
Replies: 5
Views: 783

Re: P25 Linked to will not change (cannot unlink/change TG)

I've attempted to replicate the problem you are having, but unfortunately I just can't. I run P25 on a zumspot (Original 0.4 hardware) and I also have a Zumradio (0.9 hardware) that is running as a simplex VHF system (Tait TM8110) and I'm unable to reproduce you issue on that one either. Is this a f...
by VK7HSE
Mon Apr 06, 2020 8:24 am
Forum: Radio Equipment
Topic: Australian Foundation License - Gateway function - IC9700
Replies: 17
Views: 1821

Re: Australian Foundation License - Gateway function - IC9700

Unfortunately the short answer is no. This is the reason why there's discussion happening between the ACMA and the WIA for a solution. This was a rather short sighted decision by the WIA back in 2005 to implement a non standard callsign structure. Although I do believe that it was done deliberately ...
by VK7HSE
Wed Apr 01, 2020 9:22 am
Forum: P25 Specific Support
Topic: P25 not working on YSF2NXDN on Yaesu FT70
Replies: 4
Views: 461

Re: P25 not working on YSF2NXDN on Yaesu FT70

I was going to point out the obvious that P25 will never work with ysf2nxdn! But the correct answer is above use DN for ysf2nxdn and WM for ysf2p25. One thing to note is that when using ysf2p25 and you are still in the wires-x control mode the FT-70D will only transmit in DN, so once you have setup ...