Search found 9 matches
- Sun Jan 07, 2024 6:41 pm
- Forum: Raspberry Pi Foundation Hardware
- Topic: Upgrade Pi Zero to Pi Zero 2
- Replies: 4
- Views: 16400
Re: Upgrade Pi Zero to Pi Zero 2
How difficult (or not difficult) is the upgrade? Does the PiZ 2 just plug in exactly where the PiZ 1 is? No soldering needed?
- Tue Sep 14, 2021 3:05 pm
- Forum: Pi-Star General Support
- Topic: Where is the current versions listed?
- Replies: 0
- Views: 841
Where is the current versions listed?
Is there somewhere that one can look up the most current release of the various software components of Pi-Star?
Example: My pi Star Reports:
Pi-Star:4.1.5 / Dashboard: 20210721
and
FW HS_Hat:v1.5.2
Is there a way I can verify these are the most recent versions?
Example: My pi Star Reports:
Pi-Star:4.1.5 / Dashboard: 20210721
and
FW HS_Hat:v1.5.2
Is there a way I can verify these are the most recent versions?
- Thu Aug 26, 2021 10:06 pm
- Forum: Pi-Star General Support
- Topic: Connected to WiFi but can't access Pi-Star dashboard.... after about an hour??
- Replies: 3
- Views: 1227
Re: Connected to WiFi but can't access Pi-Star dashboard.... after about an hour??
>>I've never seen a router that you couldn't update the firmware on, I have a TECHNICOLOR CGM4331COM as supplied by my cable provider, Comcast. According to Comcast: Comcast will automatically keep the firmware updated for you. As an end-user you can not do it manually and you don't need to .
- Thu Aug 26, 2021 1:36 pm
- Forum: Pi-Star General Support
- Topic: Connected to WiFi but can't access Pi-Star dashboard.... after about an hour??
- Replies: 3
- Views: 1227
Re: Connected to WiFi but can't access Pi-Star dashboard.... after about an hour??
A full reboot of the router last night and all seems well this morning..
Perhaps, somehow, the router's internal routing table was corrupt.
PS this router does not have the ability to load new firmware .. or if it does, the manual doesn't cover how to do it.
Perhaps, somehow, the router's internal routing table was corrupt.
PS this router does not have the ability to load new firmware .. or if it does, the manual doesn't cover how to do it.
- Thu Aug 26, 2021 2:33 am
- Forum: Pi-Star General Support
- Topic: Connected to WiFi but can't access Pi-Star dashboard.... after about an hour??
- Replies: 3
- Views: 1227
Re: Connected to WiFi but can't access Pi-Star dashboard.... after about an hour??
A further note .. while other computers on the net do not see the hotspot host .. the router itself shows it as connected .. at the same IP address as it had during the initial 60 minutes or so when it can be seen by other devices on the network ... It's been like, forever (months) since a rebooted ...
- Thu Aug 26, 2021 2:28 am
- Forum: Pi-Star General Support
- Topic: Connected to WiFi but can't access Pi-Star dashboard.... after about an hour??
- Replies: 3
- Views: 1227
Connected to WiFi but can't access Pi-Star dashboard.... after about an hour??
Simular to https://forum.pistar.uk/viewtopic.php?f=3&t=3741 , but with this twist: When I hard reboot my hot spot, but unplugging it, plugging it, and letting it reboot, all seems well, for about an hour or so. Then, I can't access the hotspots IP, I can't SSH to it, and the dashboard no longer ...
- Wed Jun 16, 2021 7:18 pm
- Forum: MMDVM_HS Hat(s)
- Topic: Power Setting in Expert configuration
- Replies: 1
- Views: 4320
Re: Power Setting in Expert configuration
Thanks a lot! When I looked at the [Modem] section, it is indeed set to 100.
- Wed Jun 16, 2021 3:59 pm
- Forum: MMDVM_HS Hat(s)
- Topic: Power Setting in Expert configuration
- Replies: 1
- Views: 4320
Power Setting in Expert configuration
I noticed there is a "power" setting on the MMDVM Expert configuration screen, just below the RX and TX frequency set. I'm having a hard time finding out what units this is set in and what is the allowable range. On mine, it seems to be set at ' 1' .. and that seems, well, likely low. Is t...
- Tue Feb 09, 2021 1:45 pm
- Forum: Pi-Star General Support
- Topic: What does "DMR Data" on my dashboard mean?
- Replies: 4
- Views: 2104
What does "DMR Data" on my dashboard mean?
Of late, I occasionally see the Dur(s), Loss and BER columns on the dashboard combined into a single column with the words "DMR Data" centered in the merged column. What does this mean or indicate?
See attachment for screen shot.
See attachment for screen shot.