Search found 984 matches
- Mon Jun 04, 2018 7:59 pm
- Forum: WiFi Setup
- Topic: Hot-Spot Fallback Mode - WPA Password?
- Replies: 5
- Views: 10622
Re: Hot-Spot Fallback Mode - WPA Password?
Changing the password does not currently change the password for Auto AP mode - that needs adding to the dashboard - and is coming soon...
- Sun Jun 03, 2018 11:37 am
- Forum: WiFi Setup
- Topic: Mobile Hotspot problem
- Replies: 5
- Views: 4196
Re: Mobile Hotspot problem
You can still enter the details by hand too, you don't have to scan and find the AP you want to connect to
- Sun Jun 03, 2018 11:32 am
- Forum: WiFi Setup
- Topic: Wired Ethernet/5GHz via ZUM & Pi-Star B+ ???
- Replies: 6
- Views: 6006
Re: Wired Ethernet/5GHz via ZUM & Pi-Star B+ ???
On my Pi 3B+ here, I did a total of 0 customisations, I only added my SSID and PSK as normal - and... wlan0 IEEE 802.11 ESSID:"REMOVED" Mode:Managed Frequency:5.24 GHz Access Point: F0:99:BF:06:AB:39 Bit Rate=200 Mb/s Tx-Power=31 dBm Retry short limit:7 RTS thr:off Fragment thr:off Power M...
- Sun Jun 03, 2018 11:24 am
- Forum: Friendly Arm Nano Pi Neo / Neo Air
- Topic: I want use to Serial Console port for Nextion DIsplay
- Replies: 1
- Views: 8283
Re: I want use to Serial Console port for Nextion DIsplay
I don't believe that its going to work, the serial console is used as *THE* output device on those (since there is no video) before the kernel is even booted.
If I remember right they have two UART available on the GPIO pins already, you would do better using one of those.
If I remember right they have two UART available on the GPIO pins already, you would do better using one of those.
- Thu May 31, 2018 8:23 pm
- Forum: P25 Specific Support
- Topic: Reflector Announcement - how to?
- Replies: 4
- Views: 5089
Re: Reflector Announcement - how to?
Of course the other thing to do is make your P25 reflector public, submit a pull request to put its information into the up-stream source for the P25 hosts file, and ask Jonathan nicely to add your announcement
- Wed May 30, 2018 6:03 pm
- Forum: ZUMSpot (Hat / Libre / USB)
- Topic: repeater not found
- Replies: 3
- Views: 5157
Re: repeater not found
Set the RX offset on your ZumSpot, (find this from the expert link on the config page, and then MMDVMHost)
Start at about -200 for a ZumSpot.
Start at about -200 for a ZumSpot.
- Sun May 27, 2018 10:43 pm
- Forum: Pi-Star General Support
- Topic: Dashboard = Color|Colour - Blue is new Red
- Replies: 13
- Views: 14740
Re: Dashboard = Color|Colour - Blue is new Red
I actually like the default color scheme, but have been trying out the new CSS Tool this morning and noticed a few things: The Wireless Configuration module's banner color doesn't change. I haven't been able to figure out what the BannerH2 and BannerExtText fields should do when Enabled = 1. It wou...
- Sun May 27, 2018 10:37 pm
- Forum: MMDVM_HS Hat(s)
- Topic: Strange hotspot behavior
- Replies: 8
- Views: 5111
Re: Strange hotspot behavior
You might want to try moving the TXOffset around a little, my guess is that as the board heats up, the frequency is shifting.
Try steps of 50 at a time, start at -200 and work up to +200 and see if its any better/worse at each.
Try steps of 50 at a time, start at -200 and work up to +200 and see if its any better/worse at each.
- Sun May 27, 2018 1:41 pm
- Forum: User Submitted Video Tutorials
- Topic: How to build an MMDVM hotspot tutorial
- Replies: 4
- Views: 11102
Re: How to build an MMDVM hotspot tutorial
The youtube BBCode just needs the video ID and not the whole link - keep them coming
- Sun May 27, 2018 10:19 am
- Forum: MMDVM_HS Hat(s)
- Topic: Help
- Replies: 2
- Views: 2564
Re: Help
When you TX, the source *IS* RF, so that is correct.