Search found 627 matches
- Thu Feb 13, 2020 8:29 pm
- Forum: Pi-Star General Support
- Topic: RPi 3 A+ running V4.1.0 RC7
- Replies: 9
- Views: 8898
Re: RPi 3 A+ running V4.1.0 RC7
Jason, I'm impressed! Thanks for continuing to provide so much expert help on the forum.
- Thu Feb 13, 2020 5:53 pm
- Forum: DMR Specific Support
- Topic: essid
- Replies: 1
- Views: 1625
Re: essid
I can't offer direct help, but can share one thing that might be a factor: if you make a change in the Expert Editor, and then subsequently make any change on the regular Configuration page, the changes you made in the Expert Editor will be reset (I'm not sure this applies to all changes made in the...
- Wed Feb 12, 2020 3:44 pm
- Forum: Pi-Star General Support
- Topic: RPi 3 A+ running V4.1.0 RC7
- Replies: 9
- Views: 8898
Re: RPi 3 A+ running V4.1.0 RC7
Max operating temp for an RPi is 85 C. While 50 C is warm, it shouldn't be anywhere near the point where the temp causes throttling (that should occur around 80 C). My 3B+ hotspots regularly operate as high as 60 C, with no issues. One reason I like the 3A+ hotspots is that they operate cooler than ...
- Wed Feb 05, 2020 2:46 am
- Forum: Nextion Screens
- Topic: Powering my Nextion 3.5 scrren
- Replies: 1
- Views: 2139
Re: Powering my Nextion 3.5 scrren
There are two ways I know of to connect a Nextion display: Via a USB to TTL UART CH340G Serial Converter, plugged into the RPI's USB. By connecting to the Serial through-holes on the radio/modem board. In both cases, the connection should provide the power you need, with the exception that some peop...
- Tue Feb 04, 2020 6:37 pm
- Forum: WiFi Setup
- Topic: Jumbospot WiFi issue
- Replies: 3
- Views: 3542
Re: Jumbospot WiFi issue
There are times that both will connect to my PC via WiFi and there are times when they will not. When they do not, they work in the background (I can communicate on C4FM and DMR with my radios), however I am unable to connect the jumbospots with my PC using the respective IP addresses. To me, this ...
- Tue Jan 28, 2020 2:13 pm
- Forum: Share your stuff
- Topic: 3.2 touch screen globe 8 3d printed case
- Replies: 2
- Views: 9457
Re: 3.2 touch screen globe 8 3d printed case
Nicely done!
- Thu Jan 23, 2020 3:14 pm
- Forum: D-Star Specific Support
- Topic: DMR->D-Star issues
- Replies: 8
- Views: 4956
Re: DMR->D-Star issues
I solved the DMR side. I needed to enable the Brandmeister network. Still not able to transmit to the D-Star side. I did register on D-Star. I verified that my call is showing up. FYI, if D-STAR cross modes are important to you, the *************** includes an onboard AMBE chip and can handle hardw...
- Thu Jan 23, 2020 3:09 pm
- Forum: DMR Specific Support
- Topic: 4000 activity shows on dashboard when not connected
- Replies: 4
- Views: 3241
Re: 4000 activity shows on dashboard when not connected
FYI, I saw an experimental fork of Pi-Star on GitHub yesterday, which includes a fix for the issue with TG 4000 being displayed in the Pi-Star DMR Repeater module after you key it up to disconnect from another talkgroup. With the fix applied, after keying up a group call to TG 4000, the DMR Repeater...
- Tue Jan 21, 2020 5:54 pm
- Forum: DMR Specific Support
- Topic: 4000 activity shows on dashboard when not connected
- Replies: 4
- Views: 3241
Re: 4000 activity shows on dashboard when not connected
I asked someone who knows more about BrandMeister-related stuff than I do. He said that if you key up a group call to TG 4000 in order to disconnect from another talkgroup, it is normal to then hear other people PTT 4000. When you subsequently key up another TG, it will disconnect TG 4000 and the ne...
- Wed Jan 01, 2020 8:57 pm
- Forum: MMDVM_HS Hat(s)
- Topic: MMDVM_HS Hat V 1.5.1b update
- Replies: 2
- Views: 3416
Re: MMDVM_HS Hat V 1.5.1b update
I'm guessing you mean the firmware flash command (sudo pistar-mmdvmhshatflash hs_hat, sudo pistar-mmdvmhshatflash hs_hat-12mhz, etc.)? If that's the case, then I think the MMDVM_HS v1.5.1b firmware would not be available via the regular firmware update command, since it's a pre-release. But if you w...