Page 1 of 1
CONFIGURATION
Posted: Fri Oct 18, 2019 1:45 pm
by f4eit
MMDM / Mini configuration impossible because PI-STAR / Admin not accessible which solution Thank you
Re: CONFIGURATION
Posted: Fri Oct 18, 2019 2:05 pm
by KE0FHS
Re: CONFIGURATION
Posted: Sat Oct 19, 2019 9:48 am
by f4eit
Hello
It is not the two files that I want but to be able to open my STAR / ADMIN page which will allow me to connect to Pi star configuration.
I powered my MMDVM Mini when I consult networks I do not see pi star setup. On my mini MMDVM the leds green and red flash but I do not see on his screen MMDVM nothing is registered
Re: CONFIGURATION
Posted: Sat Oct 19, 2019 12:39 pm
by W1KMC
Pi zero, Pi3 Pi4 ?
If pi3 or 4 use a wired connection - believe me, its faster .
If pi Zero - how long did you wait? The AP (access Point) mode can take up to 3 minutes to show in a wifi list
It shows as either pistar-setup, or pi-star-setup (I have seen it both ways.
If this is a new burn (new Pi-Star) then these are the names you look for -- If you changed the hostname before, (I have 2 deskstar and mobilestar) then if trying to connect to a NEW network the pistar does not know about you look for the hostname-setup instead (e.g. deskstar-setup, mobilestar-setup, etc.)
Re: CONFIGURATION
Posted: Sat Oct 19, 2019 2:08 pm
by KE0FHS
f4eit wrote: ↑Sat Oct 19, 2019 9:48 am
It is not the two files that I want but to be able to open my STAR / ADMIN page which will allow me to connect to Pi star configuration.
I powered my MMDVM Mini when I consult networks I do not see pi star setup. On my mini MMDVM the leds green and red flash but I do not see on his screen MMDVM nothing is registered
Those two tutorial videos contain the answer to your question.
Re: CONFIGURATION
Posted: Sun Oct 20, 2019 12:53 am
by w7efs
KE0FHS wrote: ↑Sat Oct 19, 2019 2:08 pmThose two tutorial videos contain the answer to your question.
The videos might not translate easily into French. Les vidéos ne traduisent pas facilement en français.
Re: CONFIGURATION
Posted: Sun Oct 20, 2019 2:14 pm
by f4eit
Impossible after click to open session pi-star message FORBITEN 403
Re: CONFIGURATION
Posted: Sun Oct 20, 2019 3:24 pm
by AF6VN
f4eit wrote: ↑Sun Oct 20, 2019 2:14 pm
Impossible after click to open session pi-star message FORBITEN 403
99% odds that you are specifying the wrong hostname on the connection attempt or you have a router that blocks LAN<>LAN web connections (or your unit is not even in the same LAN, and the configuration is for the dashboard to be "private").
Note: since I'd renamed my node as pi-star-3b, I just made an attempt to open "pi-star" (
http://pi-star/ -- nothing else) and got
http://www.pi-star.com/ which is a totally unrelated external site. I get a 404 error trying for .../admin on that. The 403 error indicates that you ARE reaching /some/ webserver -- but don't know whose.
Presuming you have not somehow changed the hostname, open a command shell and report the results of
ping pi-star
ping pi-star.local
ping pi-star-setup (also try with .local)
ping pistar-setup (also try with .local -- I believe both variations have been seen in the past)
Re: CONFIGURATION
Posted: Sun Oct 20, 2019 3:31 pm
by w7efs
f4eit, it will be much to your benefit to carefully observe
https://translate.google.com/translate? ... i-star.htm