Zum RPi: YSF not working but D-Star OK

General support for the Pi-Star System
Post Reply
W6CJ
Posts: 36
Joined: Wed Aug 19, 2020 11:02 pm

Zum RPi: YSF not working but D-Star OK

Post by W6CJ »

Hello,

Maybe someone has had this problem before?

My Zum RPi Nextion 3.5 quit working on YSF after 3 weeks.... issues are listed below:  

I cannot hear Americalink (290, 390) or other Fusion reflectors. 
I cannot perform Wires-X commands from my FT3DR (change reflectors).
My FT3D and an old Zum USB dongle are working fine on YSF, so, it's not my radio.
SERVICE STATUS on the Dashboard shows YSF PARROT in green (on).  (Maybe "Parrot" needs to be reset somehow?)
SERVICE STATUS on the Dashboard shows YSF GATEWAY is off.
NETWORK STATUS on the Dashboard shows YSF Network in red.
Nextion display shows transmission from my FT3, Callsign, BER.
No read-back from the Zumspot (YSF Parrot appears to be on, but not working)
Tried un-configuring then re-configuring YSF and default reflectors. 
Tried re-booting, re-seating, upgrades, updates, firmware.
I wonder if there is a bit of code, or an address or a port somewhere that is causing this?

D-Star still works quite well.

Thanks for enduring my beginner questions & best 73

Jay
W6CJ
AF6VN
Posts: 821
Joined: Fri Jul 20, 2018 1:15 am

Re: Zum RPi: YSF not working but D-Star OK

Post by AF6VN »

What do the log files show for YSF connection attempts?

--
AF6VN
Dennis L Bieber
W6CJ
Posts: 36
Joined: Wed Aug 19, 2020 11:02 pm

Re: Zum RPi: YSF not working but D-Star OK

Post by W6CJ »

Dennis & list, Thanks for your help!

I had a problem with the BBS, and am replying again.
Down below is a log from my Zum RPI.
The failure mode was:
- Not receiving/transmitting YSF
- PARROT tab is green, but not parroting my transmissions
- NETWORK STATUS YSF tab is red.
- "YSF NETWORK SERVICE NOT STARTED"
- Nextion display shows my RSSI, BER and callsign
- Zum RPI working great on D-Star, the YSF failure is recent.
- Tried: Reboot, upgrades, updates, firmware updates, reset.

I: 2020-08-30 16:17:35.441 This software is for use on amateur radio networks only,
I: 2020-08-30 16:17:35.441 it is to be used for educational purposes only. Its use on
I: 2020-08-30 16:17:35.441 commercial networks is strictly prohibited.
I: 2020-08-30 16:17:35.441 Copyright(C) 2015-2020 by Jonathan Naylor, G4KLX and others
M: 2020-08-30 16:17:35.441 MMDVMHost-20200615_Pi-Star_v4 is starting
M: 2020-08-30 16:17:35.441 Built 17:21:54 Jun 15 2020 (GitID #3313fe8)
I: 2020-08-30 16:17:35.441 General Parameters
I: 2020-08-30 16:17:35.441 Callsign: W6CJ
I: 2020-08-30 16:17:35.441 Id: 3150892
I: 2020-08-30 16:17:35.441 Duplex: no
I: 2020-08-30 16:17:35.441 Timeout: 240s
I: 2020-08-30 16:17:35.441 D-Star: enabled
I: 2020-08-30 16:17:35.442 DMR: disabled
I: 2020-08-30 16:17:35.442 YSF: disabled
I: 2020-08-30 16:17:35.442 P25: disabled
I: 2020-08-30 16:17:35.442 NXDN: disabled
I: 2020-08-30 16:17:35.442 POCSAG: disabled
I: 2020-08-30 16:17:35.442 FM: disabled
I: 2020-08-30 16:17:35.442 Modem Parameters
I: 2020-08-30 16:17:35.442 Port: /dev/ttyAMA0
I: 2020-08-30 16:17:35.442 Protocol: uart
I: 2020-08-30 16:17:35.442 RX Invert: no
I: 2020-08-30 16:17:35.442 TX Invert: yes
I: 2020-08-30 16:17:35.442 PTT Invert: no
I: 2020-08-30 16:17:35.442 TX Delay: 100ms
I: 2020-08-30 16:17:35.442 RX Offset: 0Hz
I: 2020-08-30 16:17:35.442 TX Offset: 0Hz
I: 2020-08-30 16:17:35.442 RX DC Offset: 0
I: 2020-08-30 16:17:35.442 TX DC Offset: 0
I: 2020-08-30 16:17:35.442 RF Level: 100.0%
I: 2020-08-30 16:17:35.442 DMR Delay: 0 (0.0ms)
I: 2020-08-30 16:17:35.442 RX Level: 50.0%
I: 2020-08-30 16:17:35.442 CW Id TX Level: 50.0%
I: 2020-08-30 16:17:35.442 D-Star TX Level: 50.0%
I: 2020-08-30 16:17:35.443 DMR TX Level: 50.0%
I: 2020-08-30 16:17:35.443 YSF TX Level: 50.0%
I: 2020-08-30 16:17:35.443 P25 TX Level: 50.0%
I: 2020-08-30 16:17:35.443 NXDN TX Level: 50.0%
I: 2020-08-30 16:17:35.443 POCSAG TX Level: 50.0%
I: 2020-08-30 16:17:35.443 FM TX Level: 50.0%
I: 2020-08-30 16:17:35.443 TX Frequency: 434100000Hz (434100000Hz)
M: 2020-08-30 16:17:35.509 Opening the MMDVM
I: 2020-08-30 16:17:37.521 MMDVM protocol version: 1, description: ZUMspot-v1.4.16 20190211 14.7456MHz ADF7021 FW by CA6JAU GitID #8cf46ca
I: 2020-08-30 16:17:37.541 Display Parameters
I: 2020-08-30 16:17:37.542 Type: Nextion
I: 2020-08-30 16:17:37.542 Port: modem
I: 2020-08-30 16:17:37.542 Brightness: 50
I: 2020-08-30 16:17:37.542 Clock Display: yes
I: 2020-08-30 16:17:37.542 Display UTC: no
I: 2020-08-30 16:17:37.542 Idle Brightness: 20
I: 2020-08-30 16:17:37.542 Temperature in Fahrenheit: no
I: 2020-08-30 16:17:37.542 Screen Layout: DIY by ON7LDS
I: 2020-08-30 16:17:37.546 Interfaces Info
I: 2020-08-30 16:17:37.547 IPv4: lo:127.0.0.1
I: 2020-08-30 16:17:37.548 IPv4: wlan0:192.168.1.2
I: 2020-08-30 16:17:37.548 Default interface is : wlan0
I: 2020-08-30 16:17:37.548 IP to show: wlan0:192.168.1.2
I: 2020-08-30 16:17:37.858 D-Star Network Parameters
I: 2020-08-30 16:17:37.858 Gateway Address: 127.0.0.1
I: 2020-08-30 16:17:37.858 Gateway Port: 20010
I: 2020-08-30 16:17:37.858 Local Port: 20011
I: 2020-08-30 16:17:37.858 Mode Hang: 20s
M: 2020-08-30 16:17:37.858 Opening D-Star network connection
I: 2020-08-30 16:17:37.859 RSSI
I: 2020-08-30 16:17:37.859 Mapping File: /usr/local/etc/RSSI.dat
I: 2020-08-30 16:17:37.863 Loaded 14 RSSI data mapping points from /usr/local/etc/RSSI.dat
I: 2020-08-30 16:17:37.863 D-Star RF Parameters
I: 2020-08-30 16:17:37.863 Module: B
I: 2020-08-30 16:17:37.863 Self Only: yes
I: 2020-08-30 16:17:37.863 Ack Reply: yes
I: 2020-08-30 16:17:37.863 Ack message: BER
I: 2020-08-30 16:17:37.863 Ack Time: 750ms
I: 2020-08-30 16:17:37.863 Error Reply: yes
I: 2020-08-30 16:17:37.863 Remote Gateway: no
I: 2020-08-30 16:17:37.863 Mode Hang: 20s
M: 2020-08-30 16:17:38.143 MMDVMHost-20200615_Pi-Star_v4 is running
M: 2020-08-30 16:17:47.100 D-Star link status set to "Not linked "
M: 2020-08-30 16:17:50.074 D-Star, received network header from W6CJ /INFO to CQCQCQ
M: 2020-08-30 16:52:04.895 D-Star, received network end of transmission from W6CJ /INFO to CQCQCQ , 2.5 seconds, 0% packet loss, BER: 0.0%
M: 2020-08-30 16:53:00.128 Closing the MMDVM
M: 2020-08-30 16:53:00.128 Closing D-Star network connection
I: 2020-08-30 16:53:00.128 MMDVMHost-20200615_Pi-Star_v4 exited on receipt of SIGTERM
I: 2020-08-30 16:53:50.984 This software is for use on amateur radio networks only,
I: 2020-08-30 16:53:50.984 it is to be used for educational purposes only. Its use on
I: 2020-08-30 16:53:50.984 commercial networks is strictly prohibited.
I: 2020-08-30 16:53:50.984 Copyright(C) 2015-2020 by Jonathan Naylor, G4KLX and others
M: 2020-08-30 16:53:50.985 MMDVMHost-20200615_Pi-Star_v4 is starting
M: 2020-08-30 16:53:50.985 Built 17:21:54 Jun 15 2020 (GitID #3313fe8)
I: 2020-08-30 16:53:50.985 General Parameters
I: 2020-08-30 16:53:50.985 Callsign: W6CJ
I: 2020-08-30 16:53:50.985 Id: 3150892
I: 2020-08-30 16:53:50.985 Duplex: no
I: 2020-08-30 16:53:50.985 Timeout: 240s
I: 2020-08-30 16:53:50.985 D-Star: disabled
I: 2020-08-30 16:53:50.985 DMR: disabled
I: 2020-08-30 16:53:50.985 YSF: enabled
I: 2020-08-30 16:53:50.985 P25: disabled
I: 2020-08-30 16:53:50.985 NXDN: disabled
I: 2020-08-30 16:53:50.985 POCSAG: disabled
I: 2020-08-30 16:53:50.985 FM: disabled
I: 2020-08-30 16:53:50.985 Modem Parameters
I: 2020-08-30 16:53:50.985 Port: /dev/ttyAMA0
I: 2020-08-30 16:53:50.985 Protocol: uart
I: 2020-08-30 16:53:50.985 RX Invert: no
I: 2020-08-30 16:53:50.985 TX Invert: yes
I: 2020-08-30 16:53:50.985 PTT Invert: no
I: 2020-08-30 16:53:50.985 TX Delay: 100ms
I: 2020-08-30 16:53:50.985 RX Offset: 0Hz
I: 2020-08-30 16:53:50.985 TX Offset: 0Hz
I: 2020-08-30 16:53:50.986 RX DC Offset: 0
I: 2020-08-30 16:53:50.986 TX DC Offset: 0
I: 2020-08-30 16:53:50.986 RF Level: 100.0%
I: 2020-08-30 16:53:50.986 DMR Delay: 0 (0.0ms)
I: 2020-08-30 16:53:50.986 RX Level: 50.0%
I: 2020-08-30 16:53:50.986 CW Id TX Level: 50.0%
I: 2020-08-30 16:53:50.986 D-Star TX Level: 50.0%
I: 2020-08-30 16:53:50.986 DMR TX Level: 50.0%
I: 2020-08-30 16:53:50.986 YSF TX Level: 50.0%
I: 2020-08-30 16:53:50.986 P25 TX Level: 50.0%
I: 2020-08-30 16:53:50.986 NXDN TX Level: 50.0%
I: 2020-08-30 16:53:50.986 POCSAG TX Level: 50.0%
I: 2020-08-30 16:53:50.986 FM TX Level: 50.0%
I: 2020-08-30 16:53:50.986 TX Frequency: 434100000Hz (434100000Hz)
M: 2020-08-30 16:53:50.987 Opening the MMDVM
I: 2020-08-30 16:53:52.999 MMDVM protocol version: 1, description: ZUMspot-v1.4.16 20190211 14.7456MHz ADF7021 FW by CA6JAU GitID #8cf46ca
I: 2020-08-30 16:53:53.019 Display Parameters
I: 2020-08-30 16:53:53.020 Type: Nextion
I: 2020-08-30 16:53:53.020 Port: modem
I: 2020-08-30 16:53:53.020 Brightness: 50
I: 2020-08-30 16:53:53.020 Clock Display: yes
I: 2020-08-30 16:53:53.020 Display UTC: no
I: 2020-08-30 16:53:53.020 Idle Brightness: 20
I: 2020-08-30 16:53:53.020 Temperature in Fahrenheit: no
I: 2020-08-30 16:53:53.020 Screen Layout: DIY by ON7LDS
I: 2020-08-30 16:53:53.020 Interfaces Info
I: 2020-08-30 16:53:53.022 IPv4: lo:127.0.0.1
I: 2020-08-30 16:53:53.022 IPv4: wlan0:192.168.1.2
I: 2020-08-30 16:53:53.022 Default interface is : wlan0
I: 2020-08-30 16:53:53.022 IP to show: wlan0:192.168.1.2
I: 2020-08-30 16:53:53.333 System Fusion Network Parameters
I: 2020-08-30 16:53:53.333 Local Address: 127.0.0.1
I: 2020-08-30 16:53:53.333 Local Port: 3200
I: 2020-08-30 16:53:53.333 Gateway Address: 127.0.0.1
I: 2020-08-30 16:53:53.333 Gateway Port: 4200
I: 2020-08-30 16:53:53.333 Mode Hang: 20s
M: 2020-08-30 16:53:53.334 Opening YSF network connection
I: 2020-08-30 16:53:53.334 RSSI
I: 2020-08-30 16:53:53.334 Mapping File: /usr/local/etc/RSSI.dat
I: 2020-08-30 16:53:53.335 Loaded 14 RSSI data mapping points from /usr/local/etc/RSSI.dat
I: 2020-08-30 16:53:53.335 YSF RF Parameters
I: 2020-08-30 16:53:53.335 Low Deviation: no
I: 2020-08-30 16:53:53.335 Remote Gateway: no
I: 2020-08-30 16:53:53.335 TX Hang: 4s
I: 2020-08-30 16:53:53.335 Self Only: yes
I: 2020-08-30 16:53:53.335 DG-ID: no
I: 2020-08-30 16:53:53.335 Mode Hang: 20s
M: 2020-08-30 16:53:53.614 MMDVMHost-20200615_Pi-Star_v4 is running
M: 2020-08-30 16:54:48.520 Closing the MMDVM
M: 2020-08-30 16:54:48.520 Closing YSF network connection
I: 2020-08-30 16:54:48.520 MMDVMHost-20200615_Pi-Star_v4 exited on receipt of SIGTERM
I: 2020-08-30 16:55:37.235 This software is for use on amateur radio networks only,
I: 2020-08-30 16:55:37.235 it is to be used for educational purposes only. Its use on
I: 2020-08-30 16:55:37.235 commercial networks is strictly prohibited.
I: 2020-08-30 16:55:37.235 Copyright(C) 2015-2020 by Jonathan Naylor, G4KLX and others
M: 2020-08-30 16:55:37.235 MMDVMHost-20200615_Pi-Star_v4 is starting
M: 2020-08-30 16:55:37.235 Built 17:21:54 Jun 15 2020 (GitID #3313fe8)
I: 2020-08-30 16:55:37.235 General Parameters
I: 2020-08-30 16:55:37.235 Callsign: W6CJ
I: 2020-08-30 16:55:37.235 Id: 3150892
I: 2020-08-30 16:55:37.235 Duplex: no
I: 2020-08-30 16:55:37.235 Timeout: 240s
I: 2020-08-30 16:55:37.235 D-Star: disabled
I: 2020-08-30 16:55:37.235 DMR: disabled
I: 2020-08-30 16:55:37.236 YSF: enabled
I: 2020-08-30 16:55:37.236 P25: disabled
I: 2020-08-30 16:55:37.236 NXDN: disabled
I: 2020-08-30 16:55:37.236 POCSAG: disabled
I: 2020-08-30 16:55:37.236 FM: disabled
I: 2020-08-30 16:55:37.236 Modem Parameters
I: 2020-08-30 16:55:37.236 Port: /dev/ttyAMA0
I: 2020-08-30 16:55:37.236 Protocol: uart
I: 2020-08-30 16:55:37.236 RX Invert: no
I: 2020-08-30 16:55:37.236 TX Invert: yes
I: 2020-08-30 16:55:37.236 PTT Invert: no
I: 2020-08-30 16:55:37.236 TX Delay: 100ms
I: 2020-08-30 16:55:37.236 RX Offset: 0Hz
I: 2020-08-30 16:55:37.236 TX Offset: 0Hz
I: 2020-08-30 16:55:37.236 RX DC Offset: 0
I: 2020-08-30 16:55:37.236 TX DC Offset: 0
I: 2020-08-30 16:55:37.236 RF Level: 100.0%
I: 2020-08-30 16:55:37.236 DMR Delay: 0 (0.0ms)
I: 2020-08-30 16:55:37.236 RX Level: 50.0%
I: 2020-08-30 16:55:37.236 CW Id TX Level: 50.0%
I: 2020-08-30 16:55:37.236 D-Star TX Level: 50.0%
I: 2020-08-30 16:55:37.236 DMR TX Level: 50.0%
I: 2020-08-30 16:55:37.236 YSF TX Level: 50.0%
I: 2020-08-30 16:55:37.237 P25 TX Level: 50.0%
I: 2020-08-30 16:55:37.237 NXDN TX Level: 50.0%
I: 2020-08-30 16:55:37.237 POCSAG TX Level: 50.0%
I: 2020-08-30 16:55:37.237 FM TX Level: 50.0%
I: 2020-08-30 16:55:37.237 TX Frequency: 434100000Hz (434100000Hz)
M: 2020-08-30 16:55:37.237 Opening the MMDVM
I: 2020-08-30 16:55:39.249 MMDVM protocol version: 1, description: ZUMspot-v1.4.16 20190211 14.7456MHz ADF7021 FW by CA6JAU GitID #8cf46ca
I: 2020-08-30 16:55:39.269 Display Parameters
I: 2020-08-30 16:55:39.270 Type: Nextion
I: 2020-08-30 16:55:39.270 Port: modem
I: 2020-08-30 16:55:39.270 Brightness: 50
I: 2020-08-30 16:55:39.270 Clock Display: yes
I: 2020-08-30 16:55:39.270 Display UTC: no
I: 2020-08-30 16:55:39.270 Idle Brightness: 20
I: 2020-08-30 16:55:39.270 Temperature in Fahrenheit: no
I: 2020-08-30 16:55:39.270 Screen Layout: DIY by ON7LDS
I: 2020-08-30 16:55:39.270 Interfaces Info
I: 2020-08-30 16:55:39.271 IPv4: lo:127.0.0.1
I: 2020-08-30 16:55:39.272 IPv4: wlan0:192.168.1.2
I: 2020-08-30 16:55:39.272 Default interface is : wlan0
I: 2020-08-30 16:55:39.272 IP to show: wlan0:192.168.1.2
I: 2020-08-30 16:55:39.582 System Fusion Network Parameters
I: 2020-08-30 16:55:39.582 Local Address: 127.0.0.1
I: 2020-08-30 16:55:39.582 Local Port: 3200
I: 2020-08-30 16:55:39.582 Gateway Address: 127.0.0.1
I: 2020-08-30 16:55:39.582 Gateway Port: 4200
I: 2020-08-30 16:55:39.582 Mode Hang: 20s
M: 2020-08-30 16:55:39.583 Opening YSF network connection
I: 2020-08-30 16:55:39.583 RSSI
I: 2020-08-30 16:55:39.583 Mapping File: /usr/local/etc/RSSI.dat
I: 2020-08-30 16:55:39.584 Loaded 14 RSSI data mapping points from /usr/local/etc/RSSI.dat
I: 2020-08-30 16:55:39.584 YSF RF Parameters
I: 2020-08-30 16:55:39.584 Low Deviation: no
I: 2020-08-30 16:55:39.584 Remote Gateway: no
I: 2020-08-30 16:55:39.584 TX Hang: 4s
I: 2020-08-30 16:55:39.584 Self Only: yes
I: 2020-08-30 16:55:39.584 DG-ID: no
I: 2020-08-30 16:55:39.584 Mode Hang: 20s
M: 2020-08-30 16:55:39.861 MMDVMHost-20200615_Pi-Star_v4 is running
M: 2020-08-30 16:56:30.230 YSF, received RF late entry from W6CJ /JAY to ALL
M: 2020-08-30 16:56:39.928 YSF, received RF end of transmission from W6CJ /JAY to ALL , 9.9 seconds, BER: 0.3%, RSSI: -47/-47/-47 dBm
M: 2020-08-30 16:56:50.299 YSF, received RF header from W6CJ /JAY to ALL
M: 2020-08-30 16:56:58.028 YSF, received RF end of transmission from W6CJ /JAY to ALL , 7.9 seconds, BER: 0.3%, RSSI: -47/-47/-47 dBm
M: 2020-08-30 16:57:07.005 YSF, received RF header from W6CJ /JAY to ALL
M: 2020-08-30 16:57:12.633 YSF, received RF end of transmission from W6CJ /JAY to ALL , 5.8 seconds, BER: 0.2%, RSSI: -47/-47/-47 dBm
M: 2020-08-30 18:00:46.485 YSF, received RF header from W6CJ /JAY to ALL
M: 2020-08-30 18:00:57.883 YSF, received RF end of transmission from W6CJ /JAY to ALL , 11.6 seconds, BER: 0.4%, RSSI: -47/-47/-47 dBm
M: 2020-08-30 18:01:15.634 YSF, received RF header from W6CJ /JAY to ALL
M: 2020-08-30 18:01:15.863 YSF, received RF end of transmission from W6CJ /JAY to ALL , 0.4 seconds, RSSI: -47/-47/-47 dBm
M: 2020-08-30 18:01:22.155 YSF, received RF header from W6CJ /JAY to ALL
M: 2020-08-30 18:01:22.383 YSF, received RF end of transmission from W6CJ /JAY to ALL , 0.4 seconds,
AF6VN
Posts: 821
Joined: Fri Jul 20, 2018 1:15 am

Re: Zum RPi: YSF not working but D-Star OK

Post by AF6VN »

For comparison, I just enabled YSF on my system (I don't have any compatible radio, so normally it is turned off)

Code: Select all

I: 2020-08-31 20:52:21.008 MMDVMHost-20200615_Pi-Star_v4 exited on receipt of SIGTERM
I: 2020-08-31 20:52:55.604 This software is for use on amateur radio networks only,
I: 2020-08-31 20:52:55.604 it is to be used for educational purposes only. Its use on
I: 2020-08-31 20:52:55.604 commercial networks is strictly prohibited.
I: 2020-08-31 20:52:55.604 Copyright(C) 2015-2020 by Jonathan Naylor, G4KLX and others
M: 2020-08-31 20:52:55.604 MMDVMHost-20200615_Pi-Star_v4 is starting
M: 2020-08-31 20:52:55.604 Built 17:21:54 Jun 15 2020 (GitID #3313fe8)
I: 2020-08-31 20:52:55.604 General Parameters
I: 2020-08-31 20:52:55.604     Callsign: AF6VN
I: 2020-08-31 20:52:55.604     Id: 1126104
I: 2020-08-31 20:52:55.604     Duplex: no
I: 2020-08-31 20:52:55.605     Timeout: 240s
I: 2020-08-31 20:52:55.605     D-Star: enabled
I: 2020-08-31 20:52:55.605     DMR: enabled
I: 2020-08-31 20:52:55.605     YSF: enabled
I: 2020-08-31 20:52:55.605     P25: disabled
I: 2020-08-31 20:52:55.605     NXDN: disabled
I: 2020-08-31 20:52:55.605     POCSAG: disabled
I: 2020-08-31 20:52:55.605     FM: disabled
I: 2020-08-31 20:52:55.605 Modem Parameters
I: 2020-08-31 20:52:55.605     Port: /dev/ttyAMA0
I: 2020-08-31 20:52:55.605     Protocol: uart
I: 2020-08-31 20:52:55.605     RX Invert: no
I: 2020-08-31 20:52:55.605     TX Invert: yes
I: 2020-08-31 20:52:55.605     PTT Invert: no
I: 2020-08-31 20:52:55.605     TX Delay: 100ms
I: 2020-08-31 20:52:55.605     RX Offset: 0Hz
I: 2020-08-31 20:52:55.605     TX Offset: 0Hz
I: 2020-08-31 20:52:55.605     RX DC Offset: 0
I: 2020-08-31 20:52:55.605     TX DC Offset: 0
I: 2020-08-31 20:52:55.605     RF Level: 100.0%
I: 2020-08-31 20:52:55.605     DMR Delay: 0 (0.0ms)
I: 2020-08-31 20:52:55.605     RX Level: 50.0%
I: 2020-08-31 20:52:55.605     CW Id TX Level: 50.0%
I: 2020-08-31 20:52:55.605     D-Star TX Level: 50.0%
I: 2020-08-31 20:52:55.605     DMR TX Level: 50.0%
I: 2020-08-31 20:52:55.605     YSF TX Level: 50.0%
I: 2020-08-31 20:52:55.605     P25 TX Level: 50.0%
I: 2020-08-31 20:52:55.605     NXDN TX Level: 50.0%
I: 2020-08-31 20:52:55.605     POCSAG TX Level: 50.0%
I: 2020-08-31 20:52:55.605     FM TX Level: 50.0%
I: 2020-08-31 20:52:55.605     TX Frequency: 446250000Hz (446250000Hz)
M: 2020-08-31 20:52:55.606 Opening the MMDVM
I: 2020-08-31 20:52:57.617 MMDVM protocol version: 1, description: DVMEGA HR3.19
I: 2020-08-31 20:52:57.637 Display Parameters
I: 2020-08-31 20:52:57.637     Type: None
W: 2020-08-31 20:52:57.637 No valid display found, disabling
I: 2020-08-31 20:52:57.637 D-Star Network Parameters
I: 2020-08-31 20:52:57.637     Gateway Address: 127.0.0.1
I: 2020-08-31 20:52:57.638     Gateway Port: 20010
I: 2020-08-31 20:52:57.638     Local Port: 20011
I: 2020-08-31 20:52:57.638     Mode Hang: 20s
M: 2020-08-31 20:52:57.638 Opening D-Star network connection
I: 2020-08-31 20:52:57.638 DMR Network Parameters
I: 2020-08-31 20:52:57.638     Address: 107.191.99.14
I: 2020-08-31 20:52:57.638     Port: 62031
I: 2020-08-31 20:52:57.638     Local: random
I: 2020-08-31 20:52:57.638     Jitter: 360ms
I: 2020-08-31 20:52:57.638     Slot 1: disabled
I: 2020-08-31 20:52:57.638     Slot 2: enabled
I: 2020-08-31 20:52:57.638     Mode Hang: 15s
I: 2020-08-31 20:52:57.638 Info Parameters
I: 2020-08-31 20:52:57.638     Callsign: AF6VN
I: 2020-08-31 20:52:57.638     RX Frequency: 446250000Hz
I: 2020-08-31 20:52:57.638     TX Frequency: 446250000Hz
I: 2020-08-31 20:52:57.638     Power: 1W
I: 2020-08-31 20:52:57.638     Latitude: 42.936100deg N
I: 2020-08-31 20:52:57.638     Longitude: -85.356598deg E
I: 2020-08-31 20:52:57.638     Height: 0m
I: 2020-08-31 20:52:57.638     Location: "Lowell, MI"
I: 2020-08-31 20:52:57.638     Description: "USA"
I: 2020-08-31 20:52:57.638     URL: "http://www.qrz.com/db/AF6VN"
M: 2020-08-31 20:52:57.638 DMR, Opening DMR Network
I: 2020-08-31 20:52:57.638 System Fusion Network Parameters
I: 2020-08-31 20:52:57.638     Local Address: 127.0.0.1
I: 2020-08-31 20:52:57.638     Local Port: 3200
I: 2020-08-31 20:52:57.638     Gateway Address: 127.0.0.1
I: 2020-08-31 20:52:57.638     Gateway Port: 4200
I: 2020-08-31 20:52:57.638     Mode Hang: 20s
M: 2020-08-31 20:52:57.639 Opening YSF network connection
I: 2020-08-31 20:52:57.639 CW Id Parameters
I: 2020-08-31 20:52:57.639     Time: 10 mins
I: 2020-08-31 20:52:57.639     Callsign: AF6VN
I: 2020-08-31 20:52:57.639 RSSI
I: 2020-08-31 20:52:57.639     Mapping File: /usr/local/etc/RSSI.dat
I: 2020-08-31 20:52:57.639 Loaded 14 RSSI data mapping points from /usr/local/etc/RSSI.dat
I: 2020-08-31 20:52:57.639 DMR Id Lookups
I: 2020-08-31 20:52:57.639     File: /usr/local/etc/DMRIds.dat
I: 2020-08-31 20:52:57.639     Reload: 24 hours
I: 2020-08-31 20:53:01.363 Loaded 171241 IDs to lookup table - /usr/local/etc/DMRIds.dat
I: 2020-08-31 20:53:01.363 D-Star RF Parameters
I: 2020-08-31 20:53:01.363     Module: B
I: 2020-08-31 20:53:01.363 Started the DMR Id lookup reload thread
I: 2020-08-31 20:53:01.363     Self Only: yes
I: 2020-08-31 20:53:01.363     Ack Reply: yes
I: 2020-08-31 20:53:01.363     Ack message: BER
I: 2020-08-31 20:53:01.364     Ack Time: 750ms
I: 2020-08-31 20:53:01.364     Error Reply: yes
I: 2020-08-31 20:53:01.364     Remote Gateway: no
I: 2020-08-31 20:53:01.364     Mode Hang: 20s
I: 2020-08-31 20:53:01.364 DMR RF Parameters
I: 2020-08-31 20:53:01.364     Id: 1126104
I: 2020-08-31 20:53:01.364     Color Code: 1
I: 2020-08-31 20:53:01.364     Self Only: yes
I: 2020-08-31 20:53:01.364     Embedded LC Only: no
I: 2020-08-31 20:53:01.364     Dump Talker Alias Data: yes
I: 2020-08-31 20:53:01.364     Prefixes: 0
I: 2020-08-31 20:53:01.364     Call Hang: 3s
I: 2020-08-31 20:53:01.364     TX Hang: 4s
I: 2020-08-31 20:53:01.364     Mode Hang: 15s
I: 2020-08-31 20:53:01.364     OVCM: off
I: 2020-08-31 20:53:01.364     DMR Roaming Beacons Type: off
I: 2020-08-31 20:53:01.364 YSF RF Parameters
I: 2020-08-31 20:53:01.364     Low Deviation: no
I: 2020-08-31 20:53:01.364     Remote Gateway: no
I: 2020-08-31 20:53:01.364     TX Hang: 4s
I: 2020-08-31 20:53:01.364     Self Only: yes
I: 2020-08-31 20:53:01.364     DG-ID: no
I: 2020-08-31 20:53:01.364     Mode Hang: 20s
M: 2020-08-31 20:53:01.364 MMDVMHost-20200615_Pi-Star_v4 is running
M: 2020-08-31 20:53:01.365 D-Star link status set to "Linking to REF030 C "
M: 2020-08-31 20:53:01.370 YSF, received network data from FCS/INFO   to ALL        at FCS002-90
M: 2020-08-31 20:53:01.370 D-Star link status set to "Linked to REF030 C  "
M: 2020-08-31 20:53:02.908 YSF, network watchdog has expired, 1.5 seconds, 0% packet loss, BER: 1.3%
M: 2020-08-31 20:53:05.687 YSF, received network data from KD4QKH     to ALL        at FCS002-90
M: 2020-08-31 20:53:09.888 YSF, network watchdog has expired, 2.9 seconds, 0% packet loss, BER: 0.0%
M: 2020-08-31 20:53:11.530 DMR, Logged into the master successfully
M: 2020-08-31 20:53:56.897 D-Star, received network header from KN4TSK  /     to CQCQCQ   via REF030 C
M: 2020-08-31 20:54:02.673 D-Star, received network end of transmission from KN4TSK  /     to CQCQCQ  , 5.8 seconds, 0% packet loss, BER: 0.2%
M: 2020-08-31 20:54:27.442 YSF, network watchdog has expired, 0.1 seconds, 0% packet loss, BER: 0.0%
M: 2020-08-31 20:54:40.455 YSF, received network data from MI7ABU     to ALL        at FCS002-90
M: 2020-08-31 20:54:42.463 YSF, network watchdog has expired, 0.6 seconds, 0% packet loss, BER: 0.0%
M: 2020-08-31 20:55:12.852 YSF, received network data from K3DY       to ALL        at FCS002-90
M: 2020-08-31 20:55:18.347 YSF, network watchdog has expired, 4.1 seconds, 0% packet loss, BER: 0.0%
M: 2020-08-31 20:55:22.566 YSF, received network data from KD4QKH     to ALL        at FCS002-90
M: 2020-08-31 20:55:29.686 YSF, network watchdog has expired, 5.7 seconds, 0% packet loss, BER: 0.0%
M: 2020-08-31 20:55:34.884 YSF, received network data from K3DY       to ALL        at FCS002-90
M: 2020-08-31 20:56:09.477 YSF, network watchdog has expired, 31.8 seconds, 0% packet loss, BER: 0.0%
M: 2020-08-31 20:56:11.461 YSF, received network data from KD4QKH     to ALL        at FCS002-90
M: 2020-08-31 20:56:40.193 YSF, network watchdog has expired, 27.1 seconds, 0% packet loss, BER: 0.0%
pi-star@pi-star-3b(ro):pi-star$
What does your YSFGateway log show? I ask as your listed log file does not show a line similar to
M: 2020-08-31 20:53:01.370 YSF, received network data from FCS/INFO to ALL at FCS002-90

Code: Select all

pi-star@pi-star-3b(ro):pi-star$ cat YSFGateway-2020-08-31.log
M: 2020-08-31 20:52:55.262 Opening YSF network connection
I: 2020-08-31 20:52:55.262 Opening UDP port on 4200
M: 2020-08-31 20:52:55.262 Opening YSF network connection
I: 2020-08-31 20:52:55.262 Opening UDP port on 42000
M: 2020-08-31 20:52:55.262 Resolving FCS00x addresses
M: 2020-08-31 20:52:56.812 Opening FCS network connection
I: 2020-08-31 20:52:56.812 Opening UDP port on 42001
I: 2020-08-31 20:52:56.812 The ID of this repeater is 10411
I: 2020-08-31 20:52:56.815 Loaded 999 FCS room descriptions
I: 2020-08-31 20:52:56.832 Loaded 912 YSF reflectors
I: 2020-08-31 20:52:56.832 Loaded YSF parrot
I: 2020-08-31 20:52:56.832 Loaded YSF2DMR
I: 2020-08-31 20:52:56.832 Loaded YSF2NXDN
I: 2020-08-31 20:52:56.832 Loaded YSF2P25
I: 2020-08-31 20:52:56.902 Opening UDP port on 6073
M: 2020-08-31 20:52:56.902 Automatic (re-)connection to FCS00290
M: 2020-08-31 20:52:56.902 Starting YSFGateway-20200503_Pi-Star_v4
M: 2020-08-31 20:52:56.982 Linked to FCS002-90
M: 2020-08-31 20:53:06.372 Link successful to MMDVM
pi-star@pi-star-3b(ro):pi-star$

--
AF6VN
Dennis L Bieber
W6CJ
Posts: 36
Joined: Wed Aug 19, 2020 11:02 pm

Re: Zum RPi: YSF not working but D-Star OK

Post by W6CJ »

Dennis and all;

I don't know how to read everything on the logs, but it looks like your log is showing YSF connecting and receiving other stations on a reflector, where my log does not show that.

I tried updates, upgrades, firmware update, and those things mentioned in my earlier posts.
I don't have a setup for writing an image to a new SD card, so haven't tried that....maybe I can just purchase an SD card with the appropriate image already on it.

Thanks & 73,
Jay
User avatar
G8SEZ
Posts: 556
Joined: Fri Apr 13, 2018 8:26 pm

Re: Zum RPi: YSF not working but D-Star OK

Post by G8SEZ »

W6CJ wrote: Wed Sep 02, 2020 3:05 pm Dennis and all;

I don't know how to read everything on the logs, but it looks like your log is showing YSF connecting and receiving other stations on a reflector, where my log does not show that.

I tried updates, upgrades, firmware update, and those things mentioned in my earlier posts.
I don't have a setup for writing an image to a new SD card, so haven't tried that....maybe I can just purchase an SD card with the appropriate image already on it.

Thanks & 73,
Jay
What is the thing stopping you with writing an image? There are good ways to do it on most OSs, but maybe it's a hardware limitation (no SD slot or adapter).
--

Brian G8SEZ
W6CJ
Posts: 36
Joined: Wed Aug 19, 2020 11:02 pm

Re: Zum RPi: YSF not working but D-Star OK

Post by W6CJ »

Thanks-
I see I have to buy a Micro SD card/USB dongle... no micro slots on the old box I'm running....unless it is possible to re-write the SD card while it's sitting in the Zum RPi?

Also wondering if there is a Zumspot (pi-star) executable repairs file that can be downloaded?

73,
Jay
W6CJ
User avatar
G8SEZ
Posts: 556
Joined: Fri Apr 13, 2018 8:26 pm

Re: Zum RPi: YSF not working but D-Star OK

Post by G8SEZ »

I'd suggest that you just buy an appropriate USB to SD card adapter, they are fairly cheap.

A few spare cards would make sense too, again they are not expensive. They often come with an adapter to full size SD if you don't buy something that supports micro SD cards directly.
--

Brian G8SEZ
W6CJ
Posts: 36
Joined: Wed Aug 19, 2020 11:02 pm

Re: Zum RPi: YSF not working but D-Star OK

Post by W6CJ »

All-
I resolved the problem (for the time being).
Although I performed a couple of factory resets; upgrades; updates - it was the third factory reset that did the trick. Operational on YSF and FCS again. Thanks for the suggestions.
73
Jay
W6CJ
Post Reply