Hello @ll,
Any news on MMDVM FW Update to version 1.6.0 ?
I ran update command at SSH and 1.5.2 is still being loaded to the MMDVM.
Any comments ?
MMDVM FW 1.6.0 ??
Re: MMDVM FW 1.6.0 ??
Yes, this update will require a newer version of mmdvmhost otherwise the current version won't recognise your modem after the update. I've run into a similar issue with two Zumradio 0.9 board that were accidently updated this morning because I didn't pay attention to the ssh session I was logged into, and they are both broken. On the Zumspot it was easy to roll back the firmware but for some reason those repeater controller boards aren't playing nice for me... So, if there's a lesson to learn here is to make sure you are on the correct terminal before you it enter!
So don't compile and update just yet otherwise you'll be left with a broken pistar and you'll have to reflash with pistar-zumspotflash rpi to get things working again...
So don't compile and update just yet otherwise you'll be left with a broken pistar and you'll have to reflash with pistar-zumspotflash rpi to get things working again...
Re: MMDVM FW 1.6.0 ??
Note that Andy has merged the commit only, what he has not done is create a release.
I was watching a G4KLX talk last night, he mentioned M17 several times and every time said "but there's no hardware".
It's just not ready for wide deployment and may well need a faster processor on the MMDVM HAT to be viable.
I was watching a G4KLX talk last night, he mentioned M17 several times and every time said "but there's no hardware".
It's just not ready for wide deployment and may well need a faster processor on the MMDVM HAT to be viable.
--
Brian G8SEZ
Brian G8SEZ
Re: MMDVM FW 1.6.0 ??
Theres custom firmware that you can load into a md380 resulting in a M17 handie.
Jonathan has also recently produced a client software that uses an attached mmdvm board as a m17 transceiver.
Sent via smoke signals from my SM-G935F M1DNS (Admin)
Jonathan has also recently produced a client software that uses an attached mmdvm board as a m17 transceiver.
Sent via smoke signals from my SM-G935F M1DNS (Admin)
Andrew M1DNS.
Pi-star Admin Team.
Pi-star Admin Team.
Re: MMDVM FW 1.6.0 ??
I thought that the md-380 was only at transmit stage and reception was still a work in progress?
Sent from my Pixel 4 XL using Tapatalk
Sent from my Pixel 4 XL using Tapatalk
Re: MMDVM FW 1.6.0 ??
There's always a desire for unobtainium.
It may be alright in sensible configurations, but with 9 possible modes it would exceed the power available in the 180MHz M4 CPUs, the newer boards are using the 260MHz M7 ARMs, and I think those actually run 2 threads per core so are much more than 50% faster.
I haven't been following this too closely, more information can be found by searching for G4KLX on the usual tube sites.
--
Brian G8SEZ
Brian G8SEZ
Re: MMDVM FW 1.6.0 ??
It covers a fair few bases, but this vid. was posted in the main mmdvm group with the announcement of the newer m17 releases.
If its not this video the account also shows using the new client software in use to tx rx a m17 signal.
https://youtu.be/_7fs1px2YT0
Sent via smoke signals from my SM-G935F M1DNS (Admin)
Andrew M1DNS.
Pi-star Admin Team.
Pi-star Admin Team.
Re: MMDVM FW 1.6.0 ??
I will have a look at that, still not sure where things are going.M1DNS wrote: ↑Fri Oct 22, 2021 6:56 am It covers a fair few bases, but this vid. was posted in the main mmdvm group with the announcement of the newer m17 releases.
If its not this video the account also shows using the new client software in use to tx rx a m17 signal.
https://youtu.be/_7fs1px2YT0
--
Brian G8SEZ
Brian G8SEZ
Re: MMDVM FW 1.6.0 ??
Just noticed that Andy has added some new M17 stuff to the dashboard code, dated 21st October, so there is movement in Pi-Star towards having this mode available in some shape or form.
I would think that a working version for all is some distance out as the code will need to mature.
I would think that a working version for all is some distance out as the code will need to mature.
--
Brian G8SEZ
Brian G8SEZ