Do not see Mode or direction displayed in Admin Display

[W7JRG]

Maybe you can help, I was able to connect to all reflectors until abut 5 months ago. I don't know what changed but I thought there may be a problem with my hot-spot so I purchased a new zumspot. Everything was configured and I received the message that I am connecting to REF001 but never see the link up. I have inserted a copy of my log when I try to link, and when I unlink to see if you can assist with this issue. Any help would be appreciated as I have not be able to use my Icom 92ad on D-star for 5 months.

Thanks
I: 2020-05-13 04:17:31.130 This software is for use on amateur radio networks only,
I: 2020-05-13 04:17:31.130 it is to be used for educational purposes only. Its use on
I: 2020-05-13 04:17:31.130 commercial networks is strictly prohibited.
I: 2020-05-13 04:17:31.130 Copyright(C) 2015-2018 by Jonathan Naylor, G4KLX and others
M: 2020-05-13 04:17:31.130 MMDVMHost-20181107_Pi-Star is starting
M: 2020-05-13 04:17:31.130 Built 09:24:10 Nov 12 2018 (GitID #9444eca)
I: 2020-05-13 04:17:31.130 General Parameters
I: 2020-05-13 04:17:31.130 Callsign: W7JRG
I: 2020-05-13 04:17:31.130 Id: 1234567
I: 2020-05-13 04:17:31.130 Duplex: no
I: 2020-05-13 04:17:31.131 Timeout: 240s
I: 2020-05-13 04:17:31.131 D-Star: enabled
I: 2020-05-13 04:17:31.131 DMR: disabled
I: 2020-05-13 04:17:31.131 YSF: disabled
I: 2020-05-13 04:17:31.131 P25: disabled
I: 2020-05-13 04:17:31.131 NXDN: disabled
I: 2020-05-13 04:17:31.131 POCSAG: disabled
I: 2020-05-13 04:17:31.131 Modem Parameters
I: 2020-05-13 04:17:31.131 Port: /dev/ttyAMA0
I: 2020-05-13 04:17:31.131 Protocol: uart
I: 2020-05-13 04:17:31.131 RX Invert: no
I: 2020-05-13 04:17:31.131 TX Invert: yes
I: 2020-05-13 04:17:31.131 PTT Invert: no
I: 2020-05-13 04:17:31.131 TX Delay: 100ms
I: 2020-05-13 04:17:31.131 RX Offset: 0Hz
I: 2020-05-13 04:17:31.131 TX Offset: 0Hz
I: 2020-05-13 04:17:31.131 RX DC Offset: 0
I: 2020-05-13 04:17:31.131 TX DC Offset: 0
I: 2020-05-13 04:17:31.131 RF Level: 100.0%
I: 2020-05-13 04:17:31.131 DMR Delay: 0 (0.0ms)
I: 2020-05-13 04:17:31.131 RX Level: 50.0%
I: 2020-05-13 04:17:31.131 CW Id TX Level: 50.0%
I: 2020-05-13 04:17:31.131 D-Star TX Level: 50.0%
I: 2020-05-13 04:17:31.131 DMR TX Level: 50.0%
I: 2020-05-13 04:17:31.131 YSF TX Level: 50.0%
I: 2020-05-13 04:17:31.131 P25 TX Level: 50.0%
I: 2020-05-13 04:17:31.132 NXDN TX Level: 50.0%
I: 2020-05-13 04:17:31.132 POCSAG TX Level: 50.0%
I: 2020-05-13 04:17:31.132 RX Frequency: 446250000Hz (446250000Hz)
I: 2020-05-13 04:17:31.132 TX Frequency: 446250000Hz (446250000Hz)
M: 2020-05-13 04:17:31.132 Opening the MMDVM
I: 2020-05-13 04:17:33.143 MMDVM protocol version: 1, description: ZUMspot-v1.4.17 20190529 14.7456MHz ADF7021 FW by CA6JAU GitID #cc451c4
I: 2020-05-13 04:17:33.164 Display Parameters
I: 2020-05-13 04:17:33.164 Type: OLED
I: 2020-05-13 04:17:33.547 D-Star Network Parameters
I: 2020-05-13 04:17:33.547 Gateway Address: 127.0.0.1
I: 2020-05-13 04:17:33.547 Gateway Port: 20010
I: 2020-05-13 04:17:33.547 Local Port: 20011
I: 2020-05-13 04:17:33.547 Mode Hang: 20s
M: 2020-05-13 04:17:33.548 Opening D-Star network connection
I: 2020-05-13 04:17:33.548 RSSI
I: 2020-05-13 04:17:33.548 Mapping File: /usr/local/etc/RSSI.dat
I: 2020-05-13 04:17:33.552 Loaded 14 RSSI data mapping points from /usr/local/etc/RSSI.dat
I: 2020-05-13 04:17:33.552 D-Star RF Parameters
I: 2020-05-13 04:17:33.552 Module: B
I: 2020-05-13 04:17:33.552 Self Only: yes
I: 2020-05-13 04:17:33.552 Ack Reply: yes
I: 2020-05-13 04:17:33.552 Ack message: BER
I: 2020-05-13 04:17:33.552 Ack Time: 750ms
I: 2020-05-13 04:17:33.552 Error Reply: yes
I: 2020-05-13 04:17:33.552 Remote Gateway: no
I: 2020-05-13 04:17:33.552 Mode Hang: 20s
I: 2020-05-13 04:17:33.686 Interfaces Info
I: 2020-05-13 04:17:33.687 IPv4: lo:127.0.0.1
I: 2020-05-13 04:17:33.687 IPv4: wlan0:192.168.1.100
I: 2020-05-13 04:17:33.687 Default interface is : wlan0
I: 2020-05-13 04:17:33.687 IP to show: wlan0:192.168.1.100
M: 2020-05-13 04:17:33.687 MMDVMHost-20181107_Pi-Star is running
M: 2020-05-13 04:17:48.828 D-Star link status set to "Not linked "
M: 2020-05-13 04:17:51.581 D-Star, received network header from W7JRG /INFO to CQCQCQ
M: 2020-05-13 04:17:54.031 D-Star, received network end of transmission, 2.6 seconds, 0% packet loss, BER: 0.0%
M: 2020-05-13 04:19:02.221 D-Star, received RF header from W7JRG /JIM to REF001CL
M: 2020-05-13 04:19:02.222 D-Star link status set to "Linking to REF001 C "
M: 2020-05-13 04:19:02.361 D-Star, received RF end of transmission, 0.4 seconds, BER: 0.0%, RSSI: -47/-47/-47 dBm
M: 2020-05-13 04:19:04.563 D-Star, received network header from W7JRG /INFO to CQCQCQ
M: 2020-05-13 04:19:11.486 D-Star, received network end of transmission, 7.1 seconds, 0% packet loss, BER: 0.0%
M: 2020-05-13 04:19:24.557 D-Star, received RF header from W7JRG /JIM to CQCQCQ
M: 2020-05-13 04:19:27.001 D-Star, received RF end of transmission, 2.7 seconds, BER: 0.0%, RSSI: -47/-47/-47 dBm
M: 2020-05-13 04:19:40.917 D-Star, received RF header from W7JRG /JIM to U
M: 2020-05-13 04:19:40.918 D-Star link status set to "Not linked "
M: 2020-05-13 04:19:40.960 D-Star, received RF end of transmission, 0.3 seconds, BER: 0.0%, RSSI: -47/-47/-47 dBm
M: 2020-05-13 04:19:43.165 D-Star, received network header from W7JRG /INFO to CQCQCQ
M: 2020-05-13 04:19:45.549 D-S

[M1DNS]

There's been a lot of requests from 001c 030c owners asking users link responsibly with their assetts they're seeing hundreds of links parked there for days on end with little actual use. They've asked users disconnect when not in use, but all that's mostly gone unheeded so now they've toughened up a little and permitting only one connection per ip. If you have more than one simultaneous connection running on a continual basis they'll ban you. So maybe you've been blocked? Simple test. if you can connect elsewhere, that might be the reason.

Sent from my SM-G935F using Tapatalk

[W7JRG]

Thanks for your thoughts, but I cannot connect to any reflector and was able to connect to all, until 5 months ago. I checked and have not been black listed but knew there would not be a reason for it. I have been using D-Star for 8 years, I am not a newbie and would never make multiple connections, so that is not even a consideration. I was hoping someone knew of some port change or other issue, that I must now make to get a link as everything else appears to be working.

[M1DNS]

Thanks for your thoughts, but I cannot connect to any reflector.

Does this include XLX, DCS, XRF reflectors also or just Dplus?

Sent from my SM-G935F using Tapatalk

[W7JRG]

Sorry for the late reply, but I cannot link to any at all. Everything appears normal, and looks like the hot spot is trying to connect but could be blocked by a port that is not open. I have been using the same router and was able to connect just fine before, that is why I asked the question regarding any change in ports used by PI-Star?

[AF6VN]

Sorry for the late reply, but I cannot link to any at all. Everything appears normal, and looks like the hot spot is trying to connect but could be blocked by a port that is not open. I have been using the same router and was able to connect just fine before, that is why I asked the question regarding any change in ports used by PI-Star?

To the best of my knowledge, the ports used are defined by the servers and protocols. Pi-Star software doesn't have a choice as to what ports to use.

[W7JRG]

Can you tell me what ports are open on your router and I will match them on my router to see if that works. Thanks

[AF6VN]

Can you tell me what ports are open on your router and I will match them on my router to see if that works. Thanks

If that is aimed at me, I've never explicitly opened any ports in my router -- uPnP between the Pi-Star R-Pi and the router seems to set up the needed ports automatically.

The only port I've ever manually set up is for the R-Pi running a web-server on port 80, using a dynamic DNS name resolution. Not having a valid SSL certificate, I haven't tried to set up HTTPS port.

The only configuration page of my router that even shows port information has just:

Code: Select all

NAT/Gaming
Hosted Applications
Service 	          Ports 	        Device              Delete
HTTP                  TCP/UDP: 80       microdiversity 	
Unprivileged HTTP     TCP/UDP: 8088	    microdiversity 	

{Hmmm, I need to recheck the DDNS provider -- to see if I'm rerouting inbound HTTP to 8088; there was a period of time when I couldn't connect to my own server and may have tried an alternate port.

[W7JRG]

Thanks for the info, I will check to see if I need to open any ports to match your settings. I do have uPnP enabled on my router, I'll get back to you with the results.

[W7JRG]

I added ports 80 and 8088 as in your table above and no change. Everything appears normal I get a green RX after transmitting in the radio info TRX section and it turns red and replies connecting to whatever Reflector I have selected, but never links so I don't hear anything. I have used the application successfully for a long time, I don't know what happened to cause my problem. The people who wrote the programming software logged on remotely and checked the configuration of my radio, and it is correct. This application has always been simple to install, could it be I need to upgrade? I am at version 3.4.17 and when I try to upgrade it responds with, I am at the latest version. I thought there was a version 4 available, is that correct? I also bought a new Zumspot thinking my old hot spot went bad apparently it did not, I'm stumped on this one. Thanks!