Connecting the new icom ID RP4010V repeater to Pi-Star

Help with D-Star related issues
Post Reply
ON4PN
Posts: 2
Joined: Wed Dec 01, 2021 8:07 pm

Connecting the new icom ID RP4010V repeater to Pi-Star

Post by ON4PN »

Hi all,

The new ID RP4010V Icom repeater module does not needs a separate controler to connect to the various D-star networks.
Connecting the previous ID RP4000V was no problem , but with the new ID RP4010V, with build in control interface, it seems not to work.
Does anyone has an idea how to connect this Icom ID RP4010v repeater to a raspi with pi-star on it ?

Thanks for your response.

73

Patrick ON4PN
F5HCC
Posts: 1
Joined: Sun Sep 09, 2018 8:17 pm

Re: Connecting the new icom ID RP4010V repeater to Pi-Star

Post by F5HCC »

Hi.

Try to contact Edgar F5FDR (ICOM France).

73 from Fabrice, F5HCC.
ON4PN
Posts: 2
Joined: Wed Dec 01, 2021 8:07 pm

Re: Connecting the new icom ID RP4010V repeater to Pi-Star

Post by ON4PN »

tnx for response, I'l give it a try.
73
Pat ON4PN
DL4STE
Posts: 2
Joined: Mon May 23, 2022 6:06 pm

Re: Connecting the new icom ID RP4010V repeater to Pi-Star

Post by DL4STE »

Hi,

we also bought an ID-RP4010V and we would like to run it on the D-Star network.
I think ircDDBGateway didn't work. Does it work with pi-star?

There is also a discussion:
https://groups.io/g/OpenDV/topic/91273580

https://github.com/g4klx/ircDDBGateway/issues/72

Thanks

73
Stephan
AF6VN
Posts: 821
Joined: Fri Jul 20, 2018 1:15 am

Re: Connecting the new icom ID RP4010V repeater to Pi-Star

Post by AF6VN »

DL4STE wrote: Wed May 25, 2022 8:17 am we also bought an ID-RP4010V and we would like to run it on the D-Star network.
I think ircDDBGateway didn't work. Does it work with pi-star?
Uhm... "pi-star" is just a bundling of otherwise separately managed software. It USES ircDDBGateway for traffic routing and MMDVMHost (unless you configure the system for DStarRepeater module instead -- which I think has much fewer capabilities) .

--
AF6VN
Dennis L Bieber
DL4STE
Posts: 2
Joined: Mon May 23, 2022 6:06 pm

Re: Connecting the new icom ID RP4010V repeater to Pi-Star

Post by DL4STE »

Is anyone here using a 4010v with pi-star or ircddbgateway?
Thanks
73
Stephan
F5FDR
Posts: 5
Joined: Sun Sep 27, 2020 2:10 pm

Re: Connecting the new icom ID RP4010V repeater to Pi-Star

Post by F5FDR »

HI,

I wrote an article for using an ID-4010V with a raspberry-pi. This article is in French:
https://www.icom-france.com/documents/2 ... 10v-fr.pdf

73 ORQ. Edgar F5FDR ;)
df1oe
Posts: 1
Joined: Thu Nov 03, 2022 1:10 pm

Re: Connecting the new icom ID RP4010V repeater to Pi-Star

Post by df1oe »

Hello
We have a issue with the configuration of the ID RP4010V. I followes (mostly) the information from Edgar F5FDR in the Setup. However, there are some other circumstances:
The pi-Star is on eth0 connected to a 44.149. ... hamnet network (auto-configured via DHCP) and the repeater is connectet to eth1 172.16.0.1 (repeater) 172.16.0.20 (pi-star).
I have the issue, that sending voice stream packets to the 44.149. xxx is not working.
After restarting the ID-RP4010 the first call goes out to the reflector and is receibved, the second call gets lost with 96% loss.

the routing table looks like this:

Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
0.0.0.0 44.149.xx.xxx 0.0.0.0 UG 202 0 0 eth0
44.149.xx.xxx 0.0.0.0 255.255.255.224 U 202 0 0 eth0
169.254.0.0 0.0.0.0 255.255.0.0 U 203 0 0 eth1
172.16.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1

Missed i some set up of the firewall? Any suggestions are welcome...

Roland , DF1OE
ve6en
Posts: 4
Joined: Wed Apr 11, 2018 12:11 pm

Re: Connecting the new icom ID RP4010V repeater to Pi-Star

Post by ve6en »

I have recently connected my pi-star to the new Icom ID RP4010V upgraded from an older Icom stack, all appears to be working and connecting to the default reflector I have programmed at start-up. However when I try to unlink or l link reflectors using the UR in my radios it doesn't work. This worked fine on the older Icom stack but not on the new repeater. Just wondering if anyone else has run into this issue.

Many thanks
Andrew VE6EN
Post Reply