VK2YMU wrote: ↑Sun Feb 03, 2019 11:23 pm
I did some testing in YSF mode (no ysf2 bridge)
I turned the two new switches off "Uppercase and Wirex pass"
I assume that this would allow me to select ysf hosts as if without the additions.
I made a video that shows this is now broken.
Please look at the video. It could just be that this is where the problem is..
I will test with another unit that has not been patched, but I note the extra buttons are now present, so you must have done an update for this. I confirm that the same issue exists with another hot spot.
It first links then unlinks, the status of the two extra switches don't seem to make any difference.
Really handy video - I think I know where the problem with that it - I have patched YSFGateway, please update and re-test for me.
I suspect that this *is* radio dependant since the FT-2D I use, does not show this behaviour.
I would also add that its well worth turning the RX offset, your WiresX commands will get much closer to 100% hit rate then.
Your fix worked a charm, thank you.
Note my board runs 0.1% BER, I knew that was not the problem, I traced the issue to a broken YSF linking as the video I made shows..
Tested on all my hotspots and its working fine.
Great stuff this is a very powerful addition to the functionality of the YSF2xx
I was thinking of creating a list of DMR talk groups to add to your list, so that TG selection of AU rooms becomes as easy as that of using a DMR radio Zone functions.
VK2YMU wrote: ↑Mon Feb 04, 2019 12:47 am
Your fix worked a charm, thank you.
Note my board runs 0.1% BER, I knew that was not the problem, I traced the issue to a broken YSF linking as the video I made shows..
Tested on all my hotspots and its working fine.
Great stuff this is a very powerful addition to the functionality of the YSF2xx
I was thinking of creating a list of DMR talk groups to add to your list, so that TG selection of AU rooms becomes as easy as that of using a DMR radio Zone functions.
Well done Andrew
Thanks for the feedback - I'll push the changes up to Jonathan's repo for the non pi-star world
Is the YSF pass-through ready on 3.14 builds? I updated and do see the "Wires-X passthrough" box, but when hitting the Wires-X button, I can only get the initial screen showing the YSF2DMR gateway, and nothing happens when I try to list talkgroups/reflectors, just 2 beeps. Looks like a really good feature and thanks for adding it; I didn't have any success before listing reflectors from the Wires-X screen even in straight YSF mode, but I'm able to get to both DMR and YSF when selecting them from the configuration on the dashboard page.
I have something odd going on with YSF2DMR + WiresX passthrough. I'm linked to the BM 206 master (Belgium).
When I'm connected to TG2061; I also get audio from e.g. 2069. trying #04000 (DTMF) / TG disconnect (from the wires-X menu) to remove all those, gives me the voice message that it's getting unlinked. However: 2069 (and other BE tg's) keep coming back. Any idea why?
Everything seems to be working fine on my FT70D. However I have a question, when using ysf2dmr and setting talk group with wires x how do I connect to a six digit talk group. Thanks
I have FTM-100DR and am wondering if there is operational info on running multiple Modes and radio control.
I can pick the Gateway for the mode I want to use, but getting confused on how to get to the Talkgroup.
I have all the YSF2XXX modes started with no "Start Talkgroup" in any. I connect to the Hotspot in Wires-X mode (hold the Dx key), select the mode, etc. Then I am stumped.
I admit I am a novice at YSF but but have lots of MMDVMHost and Pi-Star experience. We gotta get a cookbook for all the options.