Hello,
I'm new to HAM radio in general but I had no issues setting up DMR and getting it to work flawless. I got a new HT and the next challenge is DSTAR.
I have a pi3+MMDVM module, I repurposed it to use it from DMR to DSTAR (since I could not figure it out how to make both work at the same time) - it's a duplex MMDVM module.
I can connect to the DSTAR network, usually I connect on the DSC030 default reflector. I can hear other people, not problem, but when I select to use the reflector (CQCQCQ) I can send my transmission but my BER is 13-15%.
Sometimes when transmitting with this high BER, the radio makes weird noises (like interference) and will not stop until I reboot the pi3.
Any ideas how to solve this? I tried different Reflectors and no success. I'm in the US West coast.
Thank you.
New to DSTAR - Links to Reflector but BER 13%
New to DSTAR - Links to Reflector but BER 13%
- Attachments
-
- 66886509_2363200500561317_7119828580057481216_n.png (98.68 KiB) Viewed 3191 times
Re: New to DSTAR - Links to Reflector but BER 13%
Could it be that your DMR or your D-Star radio is off frequency relative to your MMDVM?
Make sure both radios are on frequency, then adjust the MMDVM for minimum BER.
73 Dave
Make sure both radios are on frequency, then adjust the MMDVM for minimum BER.
73 Dave
ID51E plus 2
ID5100E
IC9700
AnyTone AT-D878UV
Chinese MMDVM with OLED on a Pi 3B
DVAP on a Pi 3B
ID5100E
IC9700
AnyTone AT-D878UV
Chinese MMDVM with OLED on a Pi 3B
DVAP on a Pi 3B
Re: New to DSTAR - Links to Reflector but BER 13%
I got it to work.
I was using a MMDVM duplex on Simplex mode. For some reason that did not go well.
A lot of guides that you can find that talks about duplex MMDVMs are for DMR only. And almost all of the guides that I found for DSTAR uses Simplex MMDVMs.
Changed it back to Duplex, set the TX and RX frequencies.
Configured my D74 with the same TX frequency as my MMDVM and a plus offset frequency the same as the RX on the MMDVM.
Other thing that I did, I set Gateway = 1 on the Expert configuration on the pi-star.
Now everything works perfectly with both DMR and DSTAR on the same MMDVM. DSTAR in my case sounds much better than DMR.
73
Filipe
I was using a MMDVM duplex on Simplex mode. For some reason that did not go well.
A lot of guides that you can find that talks about duplex MMDVMs are for DMR only. And almost all of the guides that I found for DSTAR uses Simplex MMDVMs.
Changed it back to Duplex, set the TX and RX frequencies.
Configured my D74 with the same TX frequency as my MMDVM and a plus offset frequency the same as the RX on the MMDVM.
Other thing that I did, I set Gateway = 1 on the Expert configuration on the pi-star.
Now everything works perfectly with both DMR and DSTAR on the same MMDVM. DSTAR in my case sounds much better than DMR.
73
Filipe
- Attachments
-
- IMG_3365.jpeg (64.71 KiB) Viewed 3169 times
Re: New to DSTAR - Links to Reflector but BER 13%
Glad you got it sorted Filipe. I find the audio on D-Star sounds better on the small speaker of my ID-51, than on the larger speaker on my ID-5100.
73 Dave
73 Dave
ID51E plus 2
ID5100E
IC9700
AnyTone AT-D878UV
Chinese MMDVM with OLED on a Pi 3B
DVAP on a Pi 3B
ID5100E
IC9700
AnyTone AT-D878UV
Chinese MMDVM with OLED on a Pi 3B
DVAP on a Pi 3B