Page 4 of 4
Re: 4.2.0 Beta feedback
Posted: Fri Feb 02, 2024 10:57 am
by MW0MWZ
MW0MWZ wrote: ↑Fri Feb 02, 2024 10:55 am
The standard for D-Star is that 70cm band = "B", this is why the dashboard does that.
So looking back I did correct that some time ago, also tested on my own hot-spot on d-star, set RPT1 to "F" and it stays on F.
Clear your browser's stored form data, I have seen browsers being over-helpful and storing old data and pushing that in the form when you hit apply. Mine seems to be working as intended here.
Re: 4.2.0 Beta feedback
Posted: Sat Feb 03, 2024 5:48 pm
by PU4EXM
OrangePi not working with mmdvm.
Re: 4.2.0 Beta feedback
Posted: Sat Feb 03, 2024 10:03 pm
by MW0MWZ
PU4EXM wrote: ↑Sat Feb 03, 2024 5:48 pm
OrangePi not working with mmdvm.
I need more to go on than this....
Re: 4.2.0 Beta feedback
Posted: Sun Feb 04, 2024 1:43 am
by DW7GDL
FYI I switched to the testing branch and updated, and the problem of not being able to link (in YSF) from the admin page was back. I switched back to the master branch (and updated) and linking from the admin page works again.
Pi-Star 4.2.0 Beta, simplex MMDVM hotspot (Pi Zero W with STM32-DVM-MMDVM_HS GPIO HAT) with modes YSF, YSF2DMR and POCSAG enabled.
Re: 4.2.0 Beta feedback
Posted: Sun Feb 04, 2024 7:37 pm
by n9mxq
I have 3 duplex hotspots. (and 2 mobile). Upgraded all no problem.. The problem I'm seeing is with the pi-star.local address..
DMR=pi-star.local
DMR Mobile=pi-star1.local
YSF mobile=pi-star2.local
YSF=pi-star3.local
Dstar=Pistar5.local (too used to it to change to 4 lol)
The problem is, when accessing the dashboard I have to use the IP address on all but pi-star.local as they all show the same address and no 1,2,3,5...
Other than that, the process has been painless.
Re: 4.2.0 Beta feedback
Posted: Sun Feb 04, 2024 10:02 pm
by MW0MWZ
DW7GDL wrote: ↑Sun Feb 04, 2024 1:43 am
FYI I switched to the testing branch and updated, and the problem of not being able to link (in YSF) from the admin page was back. I switched back to the master branch (and updated) and linking from the admin page works again.
Pi-Star 4.2.0 Beta, simplex MMDVM hotspot (Pi Zero W with STM32-DVM-MMDVM_HS GPIO HAT) with modes YSF, YSF2DMR and POCSAG enabled.
Thats a little weird, since the changes to make it work are in the dashboard, and not in the binaries (where you can move back and forth to testing / current etc). I'll check it out myself here too.
Re: 4.2.0 Beta feedback
Posted: Sun Feb 04, 2024 10:02 pm
by MW0MWZ
n9mxq wrote: ↑Sun Feb 04, 2024 7:37 pm
I have 3 duplex hotspots. (and 2 mobile). Upgraded all no problem.. The problem I'm seeing is with the pi-star.local address..
DMR=pi-star.local
DMR Mobile=pi-star1.local
YSF mobile=pi-star2.local
YSF=pi-star3.local
Dstar=Pistar5.local (too used to it to change to 4 lol)
The problem is, when accessing the dashboard I have to use the IP address on all but pi-star.local as they all show the same address and no 1,2,3,5...
Other than that, the process has been painless.
Thank you, I'll check into that.
Re: 4.2.0 Beta feedback
Posted: Mon Feb 05, 2024 11:15 am
by DW7GDL
MW0MWZ wrote: ↑Sun Feb 04, 2024 10:02 pm
DW7GDL wrote: ↑Sun Feb 04, 2024 1:43 am
FYI I switched to the testing branch and updated, and the problem of not being able to link (in YSF) from the admin page was back. I switched back to the master branch (and updated) and linking from the admin page works again.
Pi-Star 4.2.0 Beta, simplex MMDVM hotspot (Pi Zero W with STM32-DVM-MMDVM_HS GPIO HAT) with modes YSF, YSF2DMR and POCSAG enabled.
Thats a little weird, since the changes to make it work are in the dashboard, and not in the binaries (where you can move back and forth to testing / current etc). I'll check it out myself here too.
Let me know if you find anything and I'll switch back to the testing branch and test it again.
Re: 4.2.0 Beta feedback
Posted: Tue Feb 06, 2024 12:42 am
by n9mxq
MW0MWZ wrote: ↑Sun Feb 04, 2024 10:02 pm
n9mxq wrote: ↑Sun Feb 04, 2024 7:37 pm
I have 3 duplex hotspots. (and 2 mobile). Upgraded all no problem.. The problem I'm seeing is with the pi-star.local address..
DMR=pi-star.local
DMR Mobile=pi-star1.local
YSF mobile=pi-star2.local
YSF=pi-star3.local
Dstar=Pistar5.local (too used to it to change to 4 lol)
The problem is, when accessing the dashboard I have to use the IP address on all but pi-star.local as they all show the same address and no 1,2,3,5...
Other than that, the process has been painless.
Thank you, I'll check into that.
It seems to have fixed itself.. They are now displaying correctly
Re: 4.2.0 Beta feedback
Posted: Tue Feb 06, 2024 5:52 pm
by KA1PIT
Pi-star 4.2.0, pi zero 2w, fm v1.6.1, dashboard 40201.
Dashboard showed tx staying on after releasing PTT. Yet on 4.1.8 everything worked.
Problem fixed with 4.2.0 release and dashboard 40206.