Hi,
I'm about to reformat the sd card and reload/flash a new latest pi-star and proceed with its config. Currently, Update is not working , there is a msg to say its running, but nothing appears other than "running". I've checked my account on https://www.radioid.net/account and it appears Brandmeister has the information but my hotspot a duplex DVBM type for its DMR config link to Brandmeister Self Care, no hotspot shows up for me to edit. I've double checked my codeplug for tx/rx or other issues but have run out of ideas. If anyone has a suggestion to try, I'd appreciate the tip. My wifif appears to be connected nothing else to check I can think of.
Thanks,
Colm
Pi-Star Brandmeister Hotspot Not Showing UP
Re: Pi-Star Brandmeister Hotspot Not Showing UP
Hi,
I think I'll try a reformat thanks for your tips there.
The hotspot is this one MMDVM DUPLEX hotspot Support P25 DMR YSF NXDN DMR SLOT 1+ SLOT 2 for Raspberry pi
I've again double checked BM Selfcare pwd and set it correctly in pi star.
I notice in live logging which doesn't appear to work but the download log works I get this msg
M: 2021-12-10 10:13:53.130 Opening the MMDVM
E: 2021-12-10 10:14:05.948 Unable to read the firmware version after six attempts
Nope I've connected to BM in the past and have the log of last successful connection about 50 days ago I've a pic of that from Brandmeister log.
There's a strange event when I try to login to the dashboard following repowering the modem, on Dashboard it goes Green for a few moments, then it goes red. Perhaps its got this firmware issue with the modem see log below.....anyhow, next I'll reformat and reload with latest pi-star distro and see what happens next after i configure dashboard again
Thanks again for reply
I think I'll try a reformat thanks for your tips there.
The hotspot is this one MMDVM DUPLEX hotspot Support P25 DMR YSF NXDN DMR SLOT 1+ SLOT 2 for Raspberry pi
I've again double checked BM Selfcare pwd and set it correctly in pi star.
I notice in live logging which doesn't appear to work but the download log works I get this msg
M: 2021-12-10 10:13:53.130 Opening the MMDVM
E: 2021-12-10 10:14:05.948 Unable to read the firmware version after six attempts
Nope I've connected to BM in the past and have the log of last successful connection about 50 days ago I've a pic of that from Brandmeister log.
There's a strange event when I try to login to the dashboard following repowering the modem, on Dashboard it goes Green for a few moments, then it goes red. Perhaps its got this firmware issue with the modem see log below.....anyhow, next I'll reformat and reload with latest pi-star distro and see what happens next after i configure dashboard again
Code: Select all
I: 2021-12-10 10:13:53.120 This software is for use on amateur radio networks only,
I: 2021-12-10 10:13:53.120 it is to be used for educational purposes only. Its use on
I: 2021-12-10 10:13:53.120 commercial networks is strictly prohibited.
I: 2021-12-10 10:13:53.120 Copyright(C) 2015-2020 by Jonathan Naylor, G4KLX and others
M: 2021-12-10 10:13:53.120 MMDVMHost-20210617_PS4 is starting
M: 2021-12-10 10:13:53.120 Built 16:32:57 Jun 17 2021 (GitID #9106fd6)
I: 2021-12-10 10:13:53.120 General Parameters
I: 2021-12-10 10:13:53.120 Callsign: EI4KO
I: 2021-12-10 10:13:53.120 Id: 2720116
I: 2021-12-10 10:13:53.120 Duplex: no
I: 2021-12-10 10:13:53.120 Timeout: 240s
I: 2021-12-10 10:13:53.120 D-Star: disabled
I: 2021-12-10 10:13:53.120 DMR: enabled
I: 2021-12-10 10:13:53.120 YSF: disabled
I: 2021-12-10 10:13:53.120 P25: disabled
I: 2021-12-10 10:13:53.121 NXDN: disabled
I: 2021-12-10 10:13:53.121 POCSAG: disabled
I: 2021-12-10 10:13:53.121 FM: disabled
I: 2021-12-10 10:13:53.121 Modem Parameters
I: 2021-12-10 10:13:53.121 Port: /dev/ttyAMA0
I: 2021-12-10 10:13:53.121 Protocol: uart
I: 2021-12-10 10:13:53.121 RX Invert: no
I: 2021-12-10 10:13:53.121 TX Invert: yes
I: 2021-12-10 10:13:53.121 PTT Invert: no
I: 2021-12-10 10:13:53.121 TX Delay: 100ms
I: 2021-12-10 10:13:53.121 RX Offset: 0Hz
I: 2021-12-10 10:13:53.121 TX Offset: 0Hz
I: 2021-12-10 10:13:53.121 RX DC Offset: 50
I: 2021-12-10 10:13:53.121 TX DC Offset: 50
I: 2021-12-10 10:13:53.121 RF Level: 100.0%
I: 2021-12-10 10:13:53.121 DMR Delay: 0 (0.0ms)
I: 2021-12-10 10:13:53.121 RX Level: 50.0%
I: 2021-12-10 10:13:53.121 CW Id TX Level: 50.0%
I: 2021-12-10 10:13:53.121 D-Star TX Level: 50.0%
I: 2021-12-10 10:13:53.121 DMR TX Level: 50.0%
I: 2021-12-10 10:13:53.121 YSF TX Level: 50.0%
I: 2021-12-10 10:13:53.121 P25 TX Level: 50.0%
I: 2021-12-10 10:13:53.121 NXDN TX Level: 50.0%
I: 2021-12-10 10:13:53.121 POCSAG TX Level: 50.0%
I: 2021-12-10 10:13:53.121 FM TX Level: 50.0%
I: 2021-12-10 10:13:53.121 TX Frequency: 434000000Hz (434000000Hz)
I: 2021-12-10 10:13:53.121 Use COS as Lockout: no
M: 2021-12-10 10:13:53.130 Opening the MMDVM
E: 2021-12-10 10:14:05.948 Unable to read the firmware version after six attempts
I: 2021-12-10 10:15:56.390 This software is for use on amateur radio networks only,
I: 2021-12-10 10:15:56.390 it is to be used for educational purposes only. Its use on
I: 2021-12-10 10:15:56.390 commercial networks is strictly prohibited.
I: 2021-12-10 10:15:56.390 Copyright(C) 2015-2020 by Jonathan Naylor, G4KLX and others
M: 2021-12-10 10:15:56.390 MMDVMHost-20210617_PS4 is starting
M: 2021-12-10 10:15:56.390 Built 16:32:57 Jun 17 2021 (GitID #9106fd6)
I: 2021-12-10 10:15:56.391 General Parameters
I: 2021-12-10 10:15:56.391 Callsign: EI4KO
I: 2021-12-10 10:15:56.391 Id: 2720116
I: 2021-12-10 10:15:56.391 Duplex: no
I: 2021-12-10 10:15:56.391 Timeout: 240s
I: 2021-12-10 10:15:56.391 D-Star: disabled
I: 2021-12-10 10:15:56.391 DMR: enabled
I: 2021-12-10 10:15:56.391 YSF: disabled
I: 2021-12-10 10:15:56.391 P25: disabled
I: 2021-12-10 10:15:56.391 NXDN: disabled
I: 2021-12-10 10:15:56.391 POCSAG: disabled
I: 2021-12-10 10:15:56.391 FM: disabled
I: 2021-12-10 10:15:56.391 Modem Parameters
I: 2021-12-10 10:15:56.391 Port: /dev/ttyAMA0
I: 2021-12-10 10:15:56.391 Protocol: uart
I: 2021-12-10 10:15:56.391 RX Invert: no
I: 2021-12-10 10:15:56.391 TX Invert: yes
I: 2021-12-10 10:15:56.391 PTT Invert: no
I: 2021-12-10 10:15:56.391 TX Delay: 100ms
I: 2021-12-10 10:15:56.391 RX Offset: 0Hz
I: 2021-12-10 10:15:56.391 TX Offset: 0Hz
I: 2021-12-10 10:15:56.391 RX DC Offset: 50
I: 2021-12-10 10:15:56.391 TX DC Offset: 50
I: 2021-12-10 10:15:56.391 RF Level: 100.0%
I: 2021-12-10 10:15:56.391 DMR Delay: 0 (0.0ms)
I: 2021-12-10 10:15:56.391 RX Level: 50.0%
I: 2021-12-10 10:15:56.391 CW Id TX Level: 50.0%
I: 2021-12-10 10:15:56.391 D-Star TX Level: 50.0%
I: 2021-12-10 10:15:56.391 DMR TX Level: 50.0%
I: 2021-12-10 10:15:56.391 YSF TX Level: 50.0%
I: 2021-12-10 10:15:56.391 P25 TX Level: 50.0%
I: 2021-12-10 10:15:56.391 NXDN TX Level: 50.0%
I: 2021-12-10 10:15:56.391 POCSAG TX Level: 50.0%
I: 2021-12-10 10:15:56.391 FM TX Level: 50.0%
I: 2021-12-10 10:15:56.391 TX Frequency: 434000000Hz (434000000Hz)
I: 2021-12-10 10:15:56.391 Use COS as Lockout: no
M: 2021-12-10 10:15:56.391 Opening the MMDVM
E: 2021-12-10 10:16:09.212 Unable to read the firmware version after six attempts
I: 2021-12-10 10:16:36.103 This software is for use on amateur radio networks only,
I: 2021-12-10 10:16:36.103 it is to be used for educational purposes only. Its use on
I: 2021-12-10 10:16:36.103 commercial networks is strictly prohibited.
I: 2021-12-10 10:16:36.103 Copyright(C) 2015-2020 by Jonathan Naylor, G4KLX and others
M: 2021-12-10 10:16:36.103 MMDVMHost-20210617_PS4 is starting
M: 2021-12-10 10:16:36.103 Built 16:32:57 Jun 17 2021 (GitID #9106fd6)
I: 2021-12-10 10:16:36.103 General Parameters
I: 2021-12-10 10:16:36.103 Callsign: EI4KO
I: 2021-12-10 10:16:36.103 Id: 2720116
I: 2021-12-10 10:16:36.103 Duplex: yes
I: 2021-12-10 10:16:36.103 Timeout: 240s
I: 2021-12-10 10:16:36.103 D-Star: disabled
I: 2021-12-10 10:16:36.103 DMR: enabled
I: 2021-12-10 10:16:36.103 YSF: disabled
I: 2021-12-10 10:16:36.103 P25: disabled
I: 2021-12-10 10:16:36.103 NXDN: disabled
I: 2021-12-10 10:16:36.103 POCSAG: disabled
I: 2021-12-10 10:16:36.103 FM: disabled
I: 2021-12-10 10:16:36.103 Modem Parameters
I: 2021-12-10 10:16:36.103 Port: /dev/ttyAMA0
I: 2021-12-10 10:16:36.103 Protocol: uart
I: 2021-12-10 10:16:36.103 RX Invert: no
I: 2021-12-10 10:16:36.103 TX Invert: yes
I: 2021-12-10 10:16:36.103 PTT Invert: no
I: 2021-12-10 10:16:36.103 TX Delay: 100ms
I: 2021-12-10 10:16:36.103 RX Offset: 0Hz
I: 2021-12-10 10:16:36.103 TX Offset: 0Hz
I: 2021-12-10 10:16:36.103 RX DC Offset: 50
I: 2021-12-10 10:16:36.103 TX DC Offset: 50
I: 2021-12-10 10:16:36.103 RF Level: 100.0%
I: 2021-12-10 10:16:36.103 DMR Delay: 0 (0.0ms)
I: 2021-12-10 10:16:36.103 RX Level: 50.0%
I: 2021-12-10 10:16:36.103 CW Id TX Level: 50.0%
I: 2021-12-10 10:16:36.103 D-Star TX Level: 50.0%
I: 2021-12-10 10:16:36.103 DMR TX Level: 50.0%
I: 2021-12-10 10:16:36.103 YSF TX Level: 50.0%
I: 2021-12-10 10:16:36.103 P25 TX Level: 50.0%
I: 2021-12-10 10:16:36.103 NXDN TX Level: 50.0%
I: 2021-12-10 10:16:36.103 POCSAG TX Level: 50.0%
I: 2021-12-10 10:16:36.103 FM TX Level: 50.0%
I: 2021-12-10 10:16:36.103 TX Frequency: 434000000Hz (434000000Hz)
I: 2021-12-10 10:16:36.103 Use COS as Lockout: no
M: 2021-12-10 10:16:36.103 Opening the MMDVM
E: 2021-12-10 10:16:48.924 Unable to read the firmware version after six attempts
I: 2021-12-10 10:18:08.486 This software is for use on amateur radio networks only,
I: 2021-12-10 10:18:08.486 it is to be used for educational purposes only. Its use on
I: 2021-12-10 10:18:08.486 commercial networks is strictly prohibited.
I: 2021-12-10 10:18:08.486 Copyright(C) 2015-2020 by Jonathan Naylor, G4KLX and others
M: 2021-12-10 10:18:08.486 MMDVMHost-20210617_PS4 is starting
M: 2021-12-10 10:18:08.486 Built 16:32:57 Jun 17 2021 (GitID #9106fd6)
I: 2021-12-10 10:18:08.486 General Parameters
I: 2021-12-10 10:18:08.486 Callsign: EI4KO
I: 2021-12-10 10:18:08.486 Id: 2720116
I: 2021-12-10 10:18:08.486 Duplex: yes
I: 2021-12-10 10:18:08.486 Timeout: 240s
I: 2021-12-10 10:18:08.486 D-Star: disabled
I: 2021-12-10 10:18:08.486 DMR: enabled
I: 2021-12-10 10:18:08.486 YSF: disabled
I: 2021-12-10 10:18:08.486 P25: disabled
I: 2021-12-10 10:18:08.486 NXDN: disabled
I: 2021-12-10 10:18:08.486 POCSAG: disabled
I: 2021-12-10 10:18:08.486 FM: disabled
I: 2021-12-10 10:18:08.486 Modem Parameters
I: 2021-12-10 10:18:08.486 Port: /dev/ttyAMA0
I: 2021-12-10 10:18:08.486 Protocol: uart
I: 2021-12-10 10:18:08.486 RX Invert: no
I: 2021-12-10 10:18:08.486 TX Invert: yes
I: 2021-12-10 10:18:08.486 PTT Invert: no
I: 2021-12-10 10:18:08.486 TX Delay: 100ms
I: 2021-12-10 10:18:08.486 RX Offset: 0Hz
I: 2021-12-10 10:18:08.486 TX Offset: 0Hz
I: 2021-12-10 10:18:08.486 RX DC Offset: 50
I: 2021-12-10 10:18:08.486 TX DC Offset: 50
I: 2021-12-10 10:18:08.486 RF Level: 100.0%
I: 2021-12-10 10:18:08.486 DMR Delay: 0 (0.0ms)
I: 2021-12-10 10:18:08.486 RX Level: 50.0%
I: 2021-12-10 10:18:08.486 CW Id TX Level: 50.0%
I: 2021-12-10 10:18:08.486 D-Star TX Level: 50.0%
I: 2021-12-10 10:18:08.486 DMR TX Level: 50.0%
I: 2021-12-10 10:18:08.487 YSF TX Level: 50.0%
I: 2021-12-10 10:18:08.487 P25 TX Level: 50.0%
I: 2021-12-10 10:18:08.487 NXDN TX Level: 50.0%
I: 2021-12-10 10:18:08.487 POCSAG TX Level: 50.0%
I: 2021-12-10 10:18:08.487 FM TX Level: 50.0%
I: 2021-12-10 10:18:08.487 TX Frequency: 434000000Hz (434000000Hz)
I: 2021-12-10 10:18:08.487 Use COS as Lockout: no
M: 2021-12-10 10:18:08.487 Opening the MMDVM
E: 2021-12-10 10:18:21.308 Unable to read the firmware version after six attempts
I: 2021-12-10 10:25:59.798 This software is for use on amateur radio networks only,
I: 2021-12-10 10:25:59.798 it is to be used for educational purposes only. Its use on
I: 2021-12-10 10:25:59.798 commercial networks is strictly prohibited.
I: 2021-12-10 10:25:59.798 Copyright(C) 2015-2020 by Jonathan Naylor, G4KLX and others
M: 2021-12-10 10:25:59.798 MMDVMHost-20210617_PS4 is starting
M: 2021-12-10 10:25:59.798 Built 16:32:57 Jun 17 2021 (GitID #9106fd6)
I: 2021-12-10 10:25:59.798 General Parameters
I: 2021-12-10 10:25:59.798 Callsign: EI4KO
I: 2021-12-10 10:25:59.798 Id: 2720116
I: 2021-12-10 10:25:59.798 Duplex: yes
I: 2021-12-10 10:25:59.798 Timeout: 240s
I: 2021-12-10 10:25:59.798 D-Star: disabled
I: 2021-12-10 10:25:59.798 DMR: enabled
I: 2021-12-10 10:25:59.798 YSF: disabled
I: 2021-12-10 10:25:59.798 P25: disabled
I: 2021-12-10 10:25:59.798 NXDN: disabled
I: 2021-12-10 10:25:59.798 POCSAG: disabled
I: 2021-12-10 10:25:59.798 FM: disabled
I: 2021-12-10 10:25:59.798 Modem Parameters
I: 2021-12-10 10:25:59.798 Port: /dev/ttyAMA0
I: 2021-12-10 10:25:59.798 Protocol: uart
I: 2021-12-10 10:25:59.798 RX Invert: no
I: 2021-12-10 10:25:59.798 TX Invert: yes
I: 2021-12-10 10:25:59.798 PTT Invert: no
I: 2021-12-10 10:25:59.798 TX Delay: 100ms
I: 2021-12-10 10:25:59.798 RX Offset: 0Hz
I: 2021-12-10 10:25:59.798 TX Offset: 0Hz
I: 2021-12-10 10:25:59.798 RX DC Offset: 50
I: 2021-12-10 10:25:59.798 TX DC Offset: 50
I: 2021-12-10 10:25:59.798 RF Level: 100.0%
I: 2021-12-10 10:25:59.798 DMR Delay: 0 (0.0ms)
I: 2021-12-10 10:25:59.798 RX Level: 50.0%
I: 2021-12-10 10:25:59.798 CW Id TX Level: 50.0%
I: 2021-12-10 10:25:59.798 D-Star TX Level: 50.0%
I: 2021-12-10 10:25:59.798 DMR TX Level: 50.0%
I: 2021-12-10 10:25:59.798 YSF TX Level: 50.0%
I: 2021-12-10 10:25:59.798 P25 TX Level: 50.0%
I: 2021-12-10 10:25:59.798 NXDN TX Level: 50.0%
I: 2021-12-10 10:25:59.798 POCSAG TX Level: 50.0%
I: 2021-12-10 10:25:59.798 FM TX Level: 50.0%
I: 2021-12-10 10:25:59.798 TX Frequency: 434000000Hz (434000000Hz)
I: 2021-12-10 10:25:59.798 Use COS as Lockout: no
M: 2021-12-10 10:25:59.799 Opening the MMDVM
E: 2021-12-10 10:26:12.619 Unable to read the firmware version after six attempts
I: 2021-12-10 10:32:33.551 This software is for use on amateur radio networks only,
I: 2021-12-10 10:32:33.551 it is to be used for educational purposes only. Its use on
I: 2021-12-10 10:32:33.551 commercial networks is strictly prohibited.
I: 2021-12-10 10:32:33.551 Copyright(C) 2015-2020 by Jonathan Naylor, G4KLX and others
M: 2021-12-10 10:32:33.551 MMDVMHost-20210617_PS4 is starting
M: 2021-12-10 10:32:33.551 Built 16:32:57 Jun 17 2021 (GitID #9106fd6)
I: 2021-12-10 10:32:33.551 General Parameters
I: 2021-12-10 10:32:33.551 Callsign: EI4KO
I: 2021-12-10 10:32:33.551 Id: 2720116
I: 2021-12-10 10:32:33.551 Duplex: yes
I: 2021-12-10 10:32:33.552 Timeout: 240s
I: 2021-12-10 10:32:33.552 D-Star: disabled
I: 2021-12-10 10:32:33.552 DMR: enabled
I: 2021-12-10 10:32:33.552 YSF: disabled
I: 2021-12-10 10:32:33.552 P25: disabled
I: 2021-12-10 10:32:33.552 NXDN: disabled
I: 2021-12-10 10:32:33.552 POCSAG: disabled
I: 2021-12-10 10:32:33.552 FM: disabled
I: 2021-12-10 10:32:33.552 Modem Parameters
I: 2021-12-10 10:32:33.552 Port: /dev/ttyAMA0
I: 2021-12-10 10:32:33.552 Protocol: uart
I: 2021-12-10 10:32:33.552 RX Invert: no
I: 2021-12-10 10:32:33.552 TX Invert: yes
I: 2021-12-10 10:32:33.552 PTT Invert: no
I: 2021-12-10 10:32:33.552 TX Delay: 100ms
I: 2021-12-10 10:32:33.552 RX Offset: 0Hz
I: 2021-12-10 10:32:33.552 TX Offset: 0Hz
I: 2021-12-10 10:32:33.552 RX DC Offset: 50
I: 2021-12-10 10:32:33.552 TX DC Offset: 50
I: 2021-12-10 10:32:33.552 RF Level: 100.0%
I: 2021-12-10 10:32:33.552 DMR Delay: 0 (0.0ms)
I: 2021-12-10 10:32:33.552 RX Level: 50.0%
I: 2021-12-10 10:32:33.552 CW Id TX Level: 50.0%
I: 2021-12-10 10:32:33.552 D-Star TX Level: 50.0%
I: 2021-12-10 10:32:33.552 DMR TX Level: 50.0%
I: 2021-12-10 10:32:33.552 YSF TX Level: 50.0%
I: 2021-12-10 10:32:33.552 P25 TX Level: 50.0%
I: 2021-12-10 10:32:33.552 NXDN TX Level: 50.0%
I: 2021-12-10 10:32:33.552 POCSAG TX Level: 50.0%
I: 2021-12-10 10:32:33.552 FM TX Level: 50.0%
I: 2021-12-10 10:32:33.552 TX Frequency: 434000000Hz (434000000Hz)
I: 2021-12-10 10:32:33.552 Use COS as Lockout: no
M: 2021-12-10 10:32:33.552 Opening the MMDVM
E: 2021-12-10 10:32:46.374 Unable to read the firmware version after six attempts
I: 2021-12-10 10:34:05.923 This software is for use on amateur radio networks only,
I: 2021-12-10 10:34:05.923 it is to be used for educational purposes only. Its use on
I: 2021-12-10 10:34:05.923 commercial networks is strictly prohibited.
I: 2021-12-10 10:34:05.923 Copyright(C) 2015-2020 by Jonathan Naylor, G4KLX and others
M: 2021-12-10 10:34:05.923 MMDVMHost-20210617_PS4 is starting
M: 2021-12-10 10:34:05.923 Built 16:32:57 Jun 17 2021 (GitID #9106fd6)
I: 2021-12-10 10:34:05.923 General Parameters
I: 2021-12-10 10:34:05.923 Callsign: EI4KO
I: 2021-12-10 10:34:05.923 Id: 2720116
I: 2021-12-10 10:34:05.924 Duplex: yes
I: 2021-12-10 10:34:05.924 Timeout: 240s
I: 2021-12-10 10:34:05.924 D-Star: disabled
I: 2021-12-10 10:34:05.924 DMR: enabled
I: 2021-12-10 10:34:05.924 YSF: disabled
I: 2021-12-10 10:34:05.924 P25: disabled
I: 2021-12-10 10:34:05.924 NXDN: disabled
I: 2021-12-10 10:34:05.924 POCSAG: disabled
I: 2021-12-10 10:34:05.924 FM: disabled
I: 2021-12-10 10:34:05.924 Modem Parameters
I: 2021-12-10 10:34:05.924 Port: /dev/ttyAMA0
I: 2021-12-10 10:34:05.924 Protocol: uart
I: 2021-12-10 10:34:05.924 RX Invert: no
I: 2021-12-10 10:34:05.924 TX Invert: yes
I: 2021-12-10 10:34:05.924 PTT Invert: no
I: 2021-12-10 10:34:05.924 TX Delay: 100ms
I: 2021-12-10 10:34:05.924 RX Offset: 0Hz
I: 2021-12-10 10:34:05.924 TX Offset: 0Hz
I: 2021-12-10 10:34:05.924 RX DC Offset: 50
I: 2021-12-10 10:34:05.924 TX DC Offset: 50
I: 2021-12-10 10:34:05.924 RF Level: 100.0%
I: 2021-12-10 10:34:05.924 DMR Delay: 0 (0.0ms)
I: 2021-12-10 10:34:05.924 RX Level: 50.0%
I: 2021-12-10 10:34:05.924 CW Id TX Level: 50.0%
I: 2021-12-10 10:34:05.924 D-Star TX Level: 50.0%
I: 2021-12-10 10:34:05.924 DMR TX Level: 50.0%
I: 2021-12-10 10:34:05.924 YSF TX Level: 50.0%
I: 2021-12-10 10:34:05.924 P25 TX Level: 50.0%
I: 2021-12-10 10:34:05.924 NXDN TX Level: 50.0%
I: 2021-12-10 10:34:05.924 POCSAG TX Level: 50.0%Re: Pi-Star Brandmeister Hotspot Not Showing UP
E: 2021-12-10 10:14:05.948 Unable to read the firmware version after six attempts
In the logs an entry starting E: indicates an error.
Either the incorrect modem selection made .
The mmdvm board isnt seated firmly on the Pi's gpio
Or incorrect firmware loaded onto the board.
Any or all of which will produce this error.
Sent via smoke signals from my SM-G935F M1DNS (Admin)
In the logs an entry starting E: indicates an error.
Either the incorrect modem selection made .
The mmdvm board isnt seated firmly on the Pi's gpio
Or incorrect firmware loaded onto the board.
Any or all of which will produce this error.
Sent via smoke signals from my SM-G935F M1DNS (Admin)
Andrew M1DNS.
Pi-star Admin Team.
Pi-star Admin Team.
Re: Pi-Star Brandmeister Hotspot Not Showing UP
Hi,
Thanks for tip re E and I notice "E: 2021-12-10 10:42:10.022 Unable to read the firmware version after six attempts"
As I mentioned Update wasn't working. I formatted the sd card using BalenaEtcher after downloading newest img file, flashed the sd card, added a wifi file using one of the tools on pi-star ...https://www.pistar.uk/downloads/# Pi-Star Tools Wifi Builder
I noticed the following "Update Nags - they are nags, no doubt, but think of them more like
a nudge to tell you when there is a new version to upgrade
to, and of course once you are at the current version, no
more nagging
."
So I'd an update nag and wasted a lot of time troubleshooting it not realising I was being "nudge to tell you when there is a new version to upgrade
to" I suggest if update doesn't load that somehow, somewhere, user is given the useful information, you need to format/load latest image...or some other solution to avoid a lot of time wasting figuring out what you should have done in the first place:-)
Good news is DMR is working I'm using FreeDMR_Ireland and its different setup to previous DMR setup. There's an options calculator I've not used but need to become more familiar with it. DMR and DMR Net are both green and TRX now showing "Listening" I've one TG setup and I call and dashboard reports the call which is good. For some reason my TYT 380 at the moment makes no sound when I key it, hope to figure that out later but things looking much better than earlier.
Takeaway from me, is if you find a couple of things not working, and solutions not working, reformat the ssd and load the latest pi-star image
Thanks
Colm
Thanks for tip re E and I notice "E: 2021-12-10 10:42:10.022 Unable to read the firmware version after six attempts"
As I mentioned Update wasn't working. I formatted the sd card using BalenaEtcher after downloading newest img file, flashed the sd card, added a wifi file using one of the tools on pi-star ...https://www.pistar.uk/downloads/# Pi-Star Tools Wifi Builder
I noticed the following "Update Nags - they are nags, no doubt, but think of them more like
a nudge to tell you when there is a new version to upgrade
to, and of course once you are at the current version, no
more nagging
."So I'd an update nag and wasted a lot of time troubleshooting it not realising I was being "nudge to tell you when there is a new version to upgrade
to" I suggest if update doesn't load that somehow, somewhere, user is given the useful information, you need to format/load latest image...or some other solution to avoid a lot of time wasting figuring out what you should have done in the first place:-)
Good news is DMR is working I'm using FreeDMR_Ireland and its different setup to previous DMR setup. There's an options calculator I've not used but need to become more familiar with it. DMR and DMR Net are both green and TRX now showing "Listening" I've one TG setup and I call and dashboard reports the call which is good. For some reason my TYT 380 at the moment makes no sound when I key it, hope to figure that out later but things looking much better than earlier.
Takeaway from me, is if you find a couple of things not working, and solutions not working, reformat the ssd and load the latest pi-star image
Thanks
Colm