forum.pistar.uk

Hello DMR friends,

a question about PrivatCall:
Is there a way to configure the DMR gateway on a SINGLE HOTSPOT (Jumbo) with PiStar so that you can select which network the private call is routed to when I call a radio friend with PrivatCall?? I have DMR friends in the Brandmeister network and friends in the IPSC2 (DMR+) network!
I haven't found a way to do this yet. ALL private calls go to the Brandmeister network!

My configuration for the Brandmeister and IPSC2 (DMR+) networks:

[DMR Network 1] BRANDMEISTER
Enabled=1
Address=2162.master.brandmeister.network
Port=62031
PassAllPC0=2
PassAllTG0=2
Password="My-Password"
Debug=0
Id=232XXXX01
Name=BM_2162_Hungary
Location=1

[DMR Network 2] IPSC2
Enabled=1
Address=89.185.97.34
Port=55555
TGRewrite0=2,1,2,1,7
TGRewrite1=2,10,2,10,80
TGRewrite2=2,100,2,100,100
TGRewrite3=2,8181,2,8181,9
TGRewrite4=2,8191,2,8191,9
TGRewrite5=2,9990,2,9990,1
TGRewrite6=2,9,2,9,1
PCRewrite0=2,9055,2,9055,6
PCRewrite1=2,4000,2,4000,1001
Password="PASSWORD"
Debug=0
Id=232XXXX01
Name=DMR+_IPSC2-OE-DMO
Location=0
Options="StartRef=4197;RelinkTime=15;UserLink=1;"

Thanks, Alfred

Look at dmrgateway rewrite rules


PassAllTG1-1
Talkgroup


PassAllPC1-1
private call



Sent via smoke signals using my SM-G935F

Hello,

"PassAllPC0=2"
It is clear to me that this line routes all private calls to the BM network! (rewrite rules)
The single HS only has one time slot!
The question again, maybe someone has the solution?

How can I control on the single hotspot whether a private call (example: PC2327114)
a) is sent to the Brandmeister network?
or
b) is sent to IPSC2 (DMR+)?

Thanks, Alfred

You can't send it to both ?? You need add rewrite rules to ech network you have active in dmrgateway

Sent via smoke signals using my SM-G960F

To enable the DMR network to be selected before sending the private call: “Brandmeister” OR “IPSC2 (DMR+)”

If it is not possible with the single hotspot, would there be a solution for the dual hotspot?

If you ARE trying to send traffic to both networks simultaneously BM have a rule, no bridging to other DMR networks.

Sent via smoke signals using my SM-G935F

The solution for a dual HS is simple:

- PC on the DUAL HS TS1 goes into the BM network
- PC on the DUAL HS TS2 goes into the IPSC2 network

[DMR Network 1]
Enabled=1
Address=2162.master.brandmeister.network
Port=62031
PassAllPC0=1
PassAllTG0=1
#PassAllPC1=2
PassAllTG1=2
Password="My Password"
Debug=0
Id=232xxxx01
Name=BM_2162_Hungary
Location=1

[DMR Network 2]
Enabled=1
Address=89.185.97.34
Port=55555
PassAllPC0=2
TGRewrite0=1,1,1,1,7
TGRewrite1=1,10,1,10,80
TGRewrite2=1,100,1,100,100
TGRewrite3=2,8181,2,8181,9
TGRewrite4=2,8191,2,8191,9
TGRewrite5=2,9990,2,9990,1
TGRewrite6=2,9,2,9,1
PCRewrite0=1,9055,1,9055,6
PCRewrite1=2,9055,2,9055,6
PCRewrite2=2,4000,2,4000,1001
Password="PASSWORD"
Debug=0
Id=232xxxx01
Name=DMR+_IPSC2-OE-DMO
Location=0
Options="StartRef=4197;RelinkTime=15;UserLink=1;

73 Alfred, OE7ABH
Greetings from Austria!
http://tyrofly.at/panos/fuegen/

PassAllPC1=1

PassAllPC1=2

Sent via smoke signals using my SM-G935F