Nextion not reading card?

All things relating to the Nextion Screen(s)
Post Reply
kp4djt
Posts: 14
Joined: Wed Feb 06, 2019 12:40 am

Nextion not reading card?

Post by kp4djt » Thu Feb 07, 2019 5:11 pm

Folks,
I have taken a couple of SD cards and reformatted them to FAT32. Placed the MMDVMHost/Nextion_G4KLX/ tft file, the one for the screen I have, a NX3224K024, on the SD cards (a 2G and a 16G) insert card into screen and all I see is:
Baud: 9600
SD Card Update.....

Unless it takes and extra ordinary amount of time to read even at 9k6b/s it should after a while clear and I believe as I understood, go to the screen on the new file. At that rate if my numbers are correct it should take about 12 minutes to load the file.

Any ideas of what maybe wrong ? If I power it down and remove the card, the power it up it goes back to the original screens with animations etc. I even removed the two data lines to make sure that was not going to cause an issue.

N3MNT
Posts: 44
Joined: Mon Sep 24, 2018 1:34 am

Re: Nextion not reading card?

Post by N3MNT » Fri Feb 08, 2019 2:24 am

Do you have the data lines disconnected ( only power and ground).

kp4djt
Posts: 14
Joined: Wed Feb 06, 2019 12:40 am

Re: Nextion not reading card?

Post by kp4djt » Sat Feb 09, 2019 1:55 am

I had not seen that the first few times I tried it, the I found the place where it said to have them disconnected, I did so but still no joy. Perhaps I messed something up and need to reset the thing?

I am going to try the one on a stand alone PI and see if that works, but It would not read the SD card. It did recognize there was a card in there but never got beyond the reading screen.

User avatar
W1KMC
Posts: 94
Joined: Wed May 02, 2018 8:34 pm
Location: Bangor, ME USA
Contact:

Re: Nextion not reading card?

Post by W1KMC » Sat Feb 09, 2019 5:33 pm

I found on my NX3224K024_011 screen that it does not like Class 10 (High Speed) cards, The class 4 works fine (small number in circle on the SD Card - you may need a magnifier to see them -- a U1 and Class 10 are the same for speed, so stay with the Class 4 and it should read just fine. If not, you're no worse for wear.
I am no developer, guru, expert, nor do I claim to be or want to be. All advice I give is purely from experience and my efforts to help others.

W1KMC - Kevin M Carman
Bangor, ME
Jumbospot on a Pi0W
DMR 3123142 & 3123143
HHUS Trunk Ext 4329

kp4djt
Posts: 14
Joined: Wed Feb 06, 2019 12:40 am

Re: Nextion not reading card?

Post by kp4djt » Tue Feb 12, 2019 7:56 am

For some reason it would not take a card unless I had formatted it using Win10. I was doing the format using Linux and formatting to Fat32 using Gparted. but that would not work, so re-looked at the docs it said to format with Windows... OK, I will do so. Formatted the card, then I moved it over to the linux
box where the tft file was for the Nextion, put the file on the card and stuck it in the Nextion, it took of and sucked up the file and displayed MMDVM on it so got that done. Now to figure out why the dual hat modem does not talk to the screen.

VK3KYY
Posts: 54
Joined: Fri Aug 03, 2018 1:31 am

Re: Nextion not reading card?

Post by VK3KYY » Tue Feb 19, 2019 2:29 am

I had similar issues

The display will only read old SD cards.

I had to scrape around and find one in an old "action camera" I bought about 4 years ago.

I'm a bit concerned my Nextion may be a clever fake, as I can't find any information elsewhere where it says they only accept old / slow SD cards

WM3M
Posts: 4
Joined: Wed Apr 11, 2018 12:35 pm

Re: Nextion not reading card?

Post by WM3M » Sat Apr 13, 2019 7:34 pm

I found same thing, had to use class 4 card, tried several newer U1 cards they would not work. Also, had to use windows 10 to format card and then copy the file onto the SD card. Once I did this it worked.
Emory WM3M

Post Reply